CutSteady CPT30008 Schnellstart-Handbuch - Seite 6
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Elektrowerkzeug CutSteady CPT30008 herunter. CutSteady CPT30008 14 Seiten.
Seite drucken
CutSteady U.S.A.
Range of use covers repair and building works, and any work from
the range of individual, amateur activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Switch
1.
Switch lock button
2.
Adaptor
3.
Dust extraction outlet
4.
Footplate
5.
Guiding roller
6.
Blade holder
7.
Guard
8.
Work speed control wheel
9.
Switch for pendulum action setting
10.
Blade protection
11.
Edge guide locking screws
12.
Laser switch
13.
Laser beam aperture
14.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Hexagonal key
1.
Dust extraction adaptor
2.
Edge guide
3.
Transport case
4.
PREPARATION FOR OPERATION
BLADE INSTALLATION
Disconnect the power tool from power supply.
Installation and removal of the blade is toolless.
• Set the switch for pendulum action (10) to position "III" and lift
the guard (8) (
• Pull lever of the blade holder (7) and slide blade into the blade
holder (7) to mechanical stop (blade teeth should be faced
forward) (
).
• Important! Make sure the blade is properly positioned in the
guiding roller (6).
• Release the lever of the blade holder (7) and ensure the blade is
• Blade removal is similar to installation, only the sequence of
actions is reversed.
Use blades suitable for T-shank holder mechanism, as shown on
DUST EXTRACTION
To improve dust extraction from processed material surface, the
• Slide adaptor (3) into the dust extraction stub (4) and turn
counter-clockwise to secure (
™
- 1 pce
- 1 pce
- 1 pce
- 1 pce
).
).
• Attach suction hose of the dust extraction system to the adaptor
(3). Make sure the connection is tight.
BLADE STORAGE
Jigsaw features convenient clip for blade storage in the rear part of
the footplate (5).
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
Before connecting the jigsaw to a power supply always check that
the power tool.
Switching on – press the switch button (1) and hold in this position.
– release pressure on the switch (1).
Locking the switch (continuous operation)
Switching on:
• Press the switch button (1) and hold in this position.
• Press the switch lock button (2) (
• Release pressure on the switch button (1).
• Press and release the switch button (1).
CONTROL OF JIGSAW OPERATION SPEED
You can control rotational speed of jigsaw motor by turning and
setting the work speed control wheel (9) in desired position. It allows
to adjust the power tool working speed to match characteristics of
processed material. Speed control range is 1 to 6.
jigsaw operation speed.
BLADE PENDULUM ACTION CONTROL
Besides reciprocating movement control there is also possibility
to set blade pendulum action level. It allows for better adjustment
of the tool operation parameters to type of processed material.
Pendulum action is controlled in steps with the switch for pendulum
action setting (10) and its range is 0 to III (
gives the best choices of pendulum action setting for various
materials:
Sheet metal plate, generally: 0
Sheet aluminium: I – II
Plywood: 0 – I
Set the switch for pendulum action to 0 when using knife blade.
Lubrication is recommended for metal cutting.
FOOTPLATE ADJUSTMENT FOR BEVEL CUTTING
Disconnect the power tool from power supply.
Adjustable jigsaw footplate allows to make a bevel cut in the range
from 0
to 45
(to either side).
0
0
• Use the hexagonal key and loosen the footplate (5
• Move the footplate (5) backwards and tilt right or left (up to 45
• Set the footplate (5) at desired angle, move forward and tighten
Scale allows for setting the footplate to angles: 0°, 15°, 30° or 45°
(right or left). Always put the hexagonal key in its storage place after
adjustment has been made.
INSTALLATION OF EDGE GUIDE
Disconnect the power tool from power supply.
Guide for parallel cutting may be installed on left or right side of the
jigsaw footplate.
6
).
). The table below
Steel sheet: 0 – I
Plastics: I – II
Wood: I - III
).
0
).