ALUZ A1-ZYZY-SQR Installationsanleitung Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Beleuchtungsanlagen ALUZ A1-ZYZY-SQR herunter. ALUZ A1-ZYZY-SQR 11 Seiten.

Seite drucken

ZYZY

Square

A1-ZYZY-SQR

WARNING

When using alumLEDs for any application, basic safety precautions should

always be followed to reduce the risk of ﬁ re, electric shock, and personal injuries.

AlumLEDs must be installed in accordance with the NEC or CEC as applicable.

ALUZ will not be responsible for any damage or malfunction caused by the

following:

• Ensure power is off before installation begins, during replacements, additions,

or repairs.

• Do not use luminaires if damaged, such as broken boards, loose connections, or

frayed wire insulation. Inspect before installing.

• Do not install luminaires in hazardous locations.

• Do not cover luminaires with any material. Covering may cause LEDs to overheat,

melt, or ignite.

• Do not paint on or over fi xture lens or LEDs.

Paint or any other substance on lens or LEDs will cause a shift in color temperature.

• Soffi t must be evenly painted with a neutral white to avoid color shift.

• Do not modify luminaires in the fi eld.

• Do not overlap luminaires in any way. (Fig. 1)

• Luminaires have line voltage risk of shock. Consult factory for any malfunctions.

Do not attempt to repair.

• Only use luminaire with specifi ed rated voltages. Do not exceed the specifi ed

voltage for any luminaire.

• Do not use extrusion as a raceway for additional wire. Non-factory feed through

wires inside luminaire will void warranty.

• Ground Fault Circuit Interrupter (GFCI) protections should be provided on circuits

or outlets when luminaire is used for outdoor applications.

• Surge protector must be set up for electrical power system to avoid damaging

lighting system.

• Do not connect wires together, follow provided wiring diagrams.

• Do not cut wire while energized. (Fig. 2)

• Do not exceed maximum run lengths.

• Do not secure luminaire with nails or like means that might damage the wiring

inside. Only secure by using mounting clips.

• Do not mount luminaire inside tanks or enclosures of any kind.

• Do not install downward facing luminaires without set screws.

• Do not use improper screw head type on mounting clips. It will cause the

mounting clip to open up and become dysfunctional.

• Do not modify mounting clips.

• Do not mount fi xture with less than the minimum number of mounting clips

required. See mounting clips section for details.

• Do not force luminaire into a space that is too small.

• Do not force luminaire with cord grip into soffi t. (Fig. 3)

• Do not install luminaire at an angle within a cove. Only install fi xtures straight

within a cove. (Fig. 4)

• Do not bend extrusion around radius.

• Do not submerge dry or wet location luminaire in any liquid.

• Do not install wet location in outdoor coves without proper drainage. (Fig. 5)

• Do not install luminaire in any area that is continuously exposed to flowing or

pooling water, such as underneath drain pipes, sprinklers, fountains, misters, etc.

• Do not cut, puncture, or penetrate aluminum housing, end caps, or lens covers.

• Do not drop, bang, or rest weight upon luminaire.

• Do not apply excessive pressure to any part of luminaire.

• Do not remove end caps from luminaire.

• Do not bend power cord or continuous connector past permitted bend radius.

Bending past permitted bend radius will break the seal of the cordgrip or

damage the insulation. (Fig. 6)

Wet Location: 3.5" minimum bend radius

Dry Location: 1.5" minimum bend radius

• Do not install in places where the power cord is subject to continuous flexing.

• Do not twist continuous connector or power cord.

• Do not hold, carry, or suspend luminaire by the power cord.

• Do not install on ceilings without mounting clips and set screws. (Fig. 7)

FIGURES

Fig. 1

Fig. 4

Fig. 6

CLEANING MATERIALS

The use of solvents and/or cleaners which are not compatible with polycarbonate

will result in the softening, crazing, and/or cracking of the plastic part. This is

especially true of polycarbonate lamps and mounting bases which may be under

stress in their normal applications.

COMPATIBLE WITH POLYCARBONATE

• Mild soap and water

• Mineral Spirits

• Isobutyl alcohol

• VM and P Naphtha

• Varsol No.2

• Mexane

• Freone TF and TE-35

• Ethanol

• Dirtex

NOT COMPATIBLE WITH POLYCARBONATE

• Trichlor

• Gasoline

• Liquid Detergents

• Acetone

• Carbon Tetrachloride

• Pink Lux (Phosphate free)

• Triclene

• Chlorinated Hydrocarbons

• #1 & #3 denatured alcohol

• Methyl Ethyl Keytone (MEK)

• Texize-8006, 8129, 8758

• MIBK

ALUZ

1170 North Red Gum Street, Anaheim, CA 92806

Phone: 800 921 2254 or 714 535 7900 | Fax: 714 535 7902 | [email protected] | aluz.lighting

Installation Instructions

Product Care & Maintenance

Fig. 2

Fig. 3

Fig. 5

Fig. 7

Set Screw

• 2% Sol. Reg. Joy

• 10% Sol Bon Ami

• White Kerosene

• Methyl alcohol

• Heptane

• Petroleum Ether/65 degrees C

• Isopropyl alcohol

• Lacryl PCL-2035 polycarbonate

cleaner

• Liquid Cleaner – 8211

• Toluol

• Agitene

• Benzol

• Ajax

• Kleenol Plastics

• Lysol

• Stanisol Naphtha

• Oils

• Lemon Joy (phosphate free)

• Diversol

• Lestoil

9 / 1 / 2021 / Rev 0

Page 2 of 11

Mounting Clip