CLOROX CLX1000 Benutzerhandbuch - Seite 8
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Farbspritzgerät CLOROX CLX1000 herunter. CLOROX CLX1000 12 Seiten. Electrostatic sprayer
Seite drucken
OPERATING INSTRUCTIONS
Preparing the Spray Area
1. Clean gross filth by using standard manual cleaning protocols.
2. Close the room to the general public for cleaning. Place signs
or warning indicators on doors that indicate no one should enter
the room.
3. Power off any sensitive electrical devices but do not unplug them.
Unit Operation/Setup
1. Choose the appropriate Clorox-approved product for cleaning,
sanitizing or disinfecting.
2. Mount desired Clorox-approved product on Clorox Total 360™
Electrostatic Sprayer base and strap into place. Ensure that the
bottles are positioned with the opening facing up and the opening
facing the dispensing tubes.
3. Unscrew the lid on the Clorox-approved product of your choice and
connect the Clorox Total 360™ Electrostatic Sprayer dispensing
cap to the bottle. Be sure the cap is screwed all the way down,
do not overtighten.
4. Unwrap electrical cord completely and plug Clorox Total 360™
Electrostatic Sprayer into a grounded, three-pronged socket.
5. Locate the On/Off switch on the base unit. Push the Total 360
Sprayer to the "On" position. A blue light will illuminate on both
the sprayer instrument panel and unit power switch.
6. Put on appropriate personal protective equipment. See section
on personal protective equipment on page 5.
7. Remove the sprayer from the unit. A blue power indicator light
should be illuminated on the sprayer.
8. The system is now ready for use.
9. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into
an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to generate a
steady flow of solution.
10 When spraying, a second blue indicator light will illuminate on the
sprayer instrument panel when the trigger is depressed.
NOTE: Sprayer will automatically stay on until trigger
is depressed an additional time.
Sprayer Operation During Cleaning
1. Position Clorox Total 360™ Electrostatic Sprayer in a rear corner
of the area.
2. Direct the nozzle at the desired surface.
3. Begin to spray. Press the sprayer button once to initiate spraying.
Press once to stop flow of the sprayer.
4. Follow a continuous path around the area working from high to low
areas moving the sprayer in a sweeping motion until surfaces are
thoroughly wet.
8 |
5. After spraying, keep the area closed to the public based
on product SDSs.
6. Remove the closed sign from the door once the reentry time
has expired.
Changing Clorox-Approved Products
1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.
2. Disconnect the bottle connection from the Clorox-approved
product that is to be changed and remove from the sprayer.
Cap the removed product if it is being stored.
3. Purging the Clorox Total 360™ Electrostatic Sprayer: Depress into
an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to purge the system.
4. Chose the appropriate Clorox-approved product for cleaning,
sanitizing or disinfecting.
5. Mount desired Clorox-approved product on Clorox Total 360™
Electrostatic Sprayer base and strap into place. Ensure that the
bottles are positioned with the opening facing up and the opening
facing the dispensing tubes.
6. Unscrew the lid on the Clorox-approved products of your
choice and connect the Clorox Total 360™ Electrostatic Sprayer
dispensing cap to the bottle. Be sure the cap is screwed all the way
down, do not overtighten.
7. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into
an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to generate a
steady flow of solution.
After Use and Storage
1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.
2. Disconnect the bottle connection from the Clorox-approved
product that is to be changed and remove from the sprayer. Cap
the removed product if it is being stored.
3. Purging the Clorox Total 360™ Electrostatic Sprayer: Depress into
an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to purge the system.
4. Turn off the unit. Blue indicator light on the instrument panel and
base of the unit should no longer be illuminated.
5. Unplug the Clorox Total 360™ Electrostatic Sprayer from wall.
6. Wrap cord on cord holder on the Clorox Total 360 base unit.
8. Store in a safe, dry place.