Ashcroft km46 Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Transmitter Ashcroft km46 herunter. Ashcroft km46 2 Seiten. Pressure transmitter
Auch für Ashcroft km46: Einbauanleitung (2 seiten)

Seite drucken

KM46 PRESSURE

TRANSMITTER INSTALLATION

INSTRUCTIONS

WARNING! READ

BEFORE INSTALLATION

1. GENERAL:

A failure resulting in injury or

damage may be caused by

excessive overpressure, excessive

vibration or pressure pulsation,

excessive instrument temperature,

corrosion of the pressure containing

parts, or other misuse. Consult

Ashcroft Inc., Stratford, Connecticut,

USA before installing if there are any

questions or concerns.

2. OVERPRESSURE:

Pressure spikes in excess of the

rated overpressure capability of the

transducer may cause irreversible

electrical and/or mechanical

damage to the pressure measuring

and containing elements.

Fluid hammer and surges can

destroy any pressure transducer and

must always be avoided. A pressure

snubber should be installed to eliminate

the damaging hammer effects. Fluid

hammer occurs when a liquid flow

is suddenly stopped, as with quick

closing solenoid valves. Surges occur

when flow is suddenly begun, as when

a pump is turned on at full power or a

valve is quickly opened.

Liquid surges are particularly

damaging to pressure transducers if

the pipe is originally empty. To avoid

damaging surges, fluid lines should

remain full (if possible), pumps should

be brought up to power slowly, and

valves opened slowly. To avoid

damage from both fluid hammer and

surges, a surge chamber should be

installed.

Symptoms of fluid hammer and surge's

damaging effects:

• Pressure transducer exhibits an

output at zero pressure (large zero

offset).

• Pressure transducer output remains

constant regardless of pressure

• In severe cases, there will be no

output.

Ashcroft Instruments GmbH

Deutschland / Germany

Max-Planck-Str. 1

D-52499 Baesweiler

Tel.: +49 (0) 2401 808-0

P/N 095I112-01EN

All specifications are subject to change without notice. All sales subject to standard terms and conditions.

FREEZING:

Prohibit freezing of media in pressure

port. Unit should be drained (mount

in vertical position with electrical

termination upward) to prevent

possible overpressure damage from

frozen media.

3. STATIC ELECTRICAL CHARGES:

Any electrical device may be

susceptible to damage when exposed

to static electrical charges. To avoid

damage to the transducer observe the

following:

• Ground the body of the transducer

BEFORE making any electrical

connections.

• When disconnecting, remove the

ground LAST!

Note: The shield and drain wire in the

cable (if supplied) is not connected

to the transducer body, and is not a

suitable ground.

DESCRIPTION

The Ashcroft Model KM46 pressure

transducer is a high performance

instrument intended for use in

applications where the process media is

compatible with Titanium sensor material

and process connection.

MECHANICAL INSTALLATION

Environmental

The KM46 transducer can be stored

within a temperature limit of -40°C to

125°C (-40°F to 257°F) and operated

within a temperature limits of -40°C to

105°C (-40°F to 221°F). IP65 or IP67

(ingress protection) rating applies for most

configurations depending on electrical

connection, install accordingly.

[email protected]

ashcroft.eu

For more information on support and

local partners please visit our web

page at ashcroft.eu or follow the

QR-Code

Mounting

The KM46 transmitter requires no special

mounting hardware and can be mounted

in any orientation with negligible position

error. Although the units can withstand

considerable vibration without damage or

significant output effects, it is always good

practice to mount the transducer where

there is minimum vibration. For units with

NPT type pressure fittings apply sealing

tape or an equivalent sealant to the

threads before installing. When installing or

removing the unit apply a wrench to the hex

wrench flats, located above the pressure

fitting.

DO NOT tighten by using a pipe wrench on

the housing. A 22 mm (

⁄

'') wrench can be

used on the wrench flats of the hex (as per

DIN 894 or similar) with a tightening torque

of ~25 Nm (20 ft lbs). For KM46 models

with detachable electrical connectors a

6 point deep socket can also be used to

install the unit.

Electro-Magnetic Interference

The circuitry of the KM46 transmitter

is designed to minimize the effect of

electromagnetic and radio frequency

interference. To minimize susceptibility

to noise, avoid running the termination

wiring in a conduit which contains high

current AC power cables. Where possible

avoid running the termination wiring near

inductive equipment.

Field Adjustments

The KM46 transmitter is precisely

calibrated and temperature compensated

at the factory to ensure long and stable

performance. There are no field accessible

adjustments on the KM46 transmitter.

ELECTRICAL INSTALLATION

Please refer to the reverse of this page

for power supply requirements and for

appropriate wiring protocol based on

the particular output signal and electrical

termination features of the unit being

installed.

Page 1