Cloud VA2120 Installationshandbuch - Seite 5
Blättern Sie online oder laden Sie pdf Installationshandbuch für Verstärken Cloud VA2120 herunter. Cloud VA2120 13 Seiten.
Seite drucken
Important
Read this before connecting the amplifier to AC mains
VA Series amplifiers are pre-configured at the factory to operate on either a 115 V or a 230 V AC mains supply.
Before applying power to the unit, please check the rear panel to ensure that the version you have is correctly set
for your local supply voltage.
The MAINS VOLTAGE SELECTOR switch on the rear panel will show either 230 V or 115 V, as shown below.
The warning sticker above the switch will confirm the factory setting.
WARNING!
CAUTION:
REPLACE WITH SAME TYPE
T2AH 250V FUSE
THIS PRODUCT IS FACTORY
CONFIGURED FOR 230V SUPPLY.
ATTENTION:
BEFORE POWERING, VERIFY THAT
UTILIZER UN FUSIBLE DE RECHARGE DE
THIS MATCHES THE SUPPLY
MEME TYPE DE T2AH 250V.
VOLTAGE OF THE INSTALLATION.
POWER INPUT
POWER INPUT
Introduction
The Cloud VA2120 and VA4120 are cost-effective audio power amplifiers for use in all types of commercial premises. They have
been designed to be as simple to install and operate as possible.
The two models are identical in terms of facilities, and differ only in the number of channels: two (VA2120) or four (VA4120).
Each channel can deliver 120 W. The amplifiers can drive either low-impedance loudspeakers directly (4 ohms minimum) or
25/70/100 V-line loudspeaker distribution systems via the tapped secondary winding of the internally fitted line transformer.
Both models of amplifier are shipped ready for connection to 25/70/100 V-line systems. Instructions on converting the outputs
for low-impedance operation can be found on page 8.
The amplifiers incorporate a limiter in each channel to protect both the output stage and loudspeakers. This reduces excessive
signal levels to ensure that clipping does not occur. Further protection circuitry disconnects the output if the maximum
permitted internal temperature is exceeded, or if DC is detected at the output terminals.
All connections are made on the rear panel, using detachable screw-terminal type connectors (Phoenix-compatible). Each
channel has a preset level control and a switchable high-pass flter to mitigate the effect of transformer saturation at low
frequencies when driving 25/70/100 V-line systems.
The front panel has a set of LEDs for each channel, confirming signal presence, excessive level and amplifier protection activity.
Both models are forced-air cooled by fans mounted on the rear panel; airflow is front-to-rear.
WARNING!
CAUTION:
MAX: 241 W
MAX: 241 W
REPLACE WITH SAME TYPE
POWER
T2AH 250V FUSE
THIS PRODUCT IS FACTORY
CONFIGURED FOR 230V SUPPLY.
ATTENTION:
BEFORE POWERING, VERIFY THAT
40-60 Hz
UTILIZER UN FUSIBLE DE RECHARGE DE
THIS MATCHES THE SUPPLY
230V ±10%
230V ±10%
MEME TYPE DE T2AH 250V.
VOLTAGE OF THE INSTALLATION.
DO NOT CONNECT YOUR VA SERIES AMPLIFIER TO AN AC SUPPLY
WITHOUT FIRST VERIFYING THE VOLTAGE SETTING.
POWER
40-60 Hz
115
POWER INPUT
WARNING!
WARNING!
CAUTION:
MAX: 241 W
REPLACE WITH SAME TYPE
T4AH 250V FUSE
THIS PRODUCT IS FACTORY
THIS PRODUCT IS FACTORY
CONFIGURED FOR 115V SUPPLY.
CONFIGURED FOR 115V SUPPLY.
ATTENTION:
BEFORE POWERING, VERIFY THAT
BEFORE POWERING, VERIFY THAT
UTILIZER UN FUSIBLE DE RECHARGE DE
THIS MATCHES THE SUPPLY
THIS MATCHES THE SUPPLY
115V ±10%
MEME TYPE DE T4AH 250V.
VOLTAGE OF THE INSTALLATION.
VOLTAGE OF THE INSTALLATION.
VA2120
115
POWER INPUT
VA Series Installation Guide V1.0
CAUTION:
MAX: 241 W
REPLACE WITH SAME TYPE
POWER
POWER
T4AH 250V FUSE
40-60 Hz
ATTENTION:
40-60 Hz
UTILIZER UN FUSIBLE DE RECHARGE DE
115V ±10%
MEME TYPE DE T4AH 250V.
VA2120
5