Cypress CSC-1600HD Betriebshandbuch - Seite 7

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Medienkonverter Cypress CSC-1600HD herunter. Cypress CSC-1600HD 12 Seiten. Cypress video scaler csc-1600hd operation manual

Seite drucken

9. OSD Menu Operation

Vertical frequency rate adjust- When it is selected it allows you to choose different

OSD display- It allows you to enable or disable the OSD display of the output

information appeared on the upper left corner of the screen.

Output Terminal - This allows you to choose which one of the two output terminals,

IR Sensor- This allows you to enable or disable the IR sensor for the Remote control.

When it is disabled the command issued from the remote control can not be

received by the main unit.

Front Panel Lockout- Under certain circumstances it may be desirable to disable the Front Panel

10. Remote Control

1. Power: Power ON/OFF button.

2. Display: Press the button to enable or disable the ON

Screen Display of the input/output information.

3. C-Video: Press the button to select composite video

as input source.

4. S-Video: Press the button to select S-Video as input source.

5. YCbCr: Press the button to select YCbCr as input source.

6. PC: Press the button to select PC input looping through

to the output.

7. VGA: Press the button to slect 640 x 480 as output resolution.

8. SVGA: Press the button to select 800 x 600 as output resolution.

9. XGA: Press the button to select 1024 x 768

as output resolution.

10. SXGA: Press the button to select 1280 x 1024

as output resolution.

11. WXGA: Press the button to select 1280 x 768

as output resolution.

12. 480p: Press the button to select 852 x 480p as output

resolution.

13. 576p: Press the button to select 852 x 576p as output

resolution.

14. 720p: Press the button to select 1280 x 702p as output resolution.

15. 1080i: Press the button to select 1920 x 1080i (interlaced) as output resolution.

16. 1365 x 768: Press the button to select 1365 x 768 as output resolution.

17. HD-15: Press the button to select 15 pin D-sub connector as output terminal.

18. BNC: Press the button to select RGBHV BNC connector as output terminal.

19. Menu: Press the button to enter into main menu page or to exit from a sub-menu.

20. Enter : Press the button to confirm your selection of an adjustment parameter.

21.  : Press the  or  to move up or move down the hight-light bar to a desired

parameter.

22.  : Press the button to increase or decrease the value of the selected parameter.

vertical frequency while under VGA, SVGA or XGA modes.

The higher the vertical refresh rate the less flicker the

picture will be. When the vertical refresh rate of an output

mode is changed, so will its horizontal scanning rate. please

refer to specification page-for cross relationship between

vertical and horizontal scanning rate.

HD-15 or BNC, will have the output signal.

When one is selected the other won't have signal.

Conrols. For example, to prevent unauthorized or accidental changes to

the setting while the unit is in use. To disable the Front Panel Controls.

press MENU, choose the Front Panel Lockout section and press ENTER.

Then you may choose Front Panel Controls OFF. In the OFF position, the

unit will not respond to commands from the Front Panel.

To return to normal operation, press and hold simultaneously the + and -

buttons for 3 seconds or use the IR Remote Control to gain access to the

Menu or use the RS-232 commaands.

POWER

DISPLAY

XGA

VGA

SVGA

C-VIDEO

SXGA

WXGA

480p

S-VIDEO

576p

720p

1080i

YCbCr

1365X768

HD-15

BNC

CR-16

ENTER