Ashly MX-206 Betriebshandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Betriebshandbuch für Musik Mixer Ashly MX-206 herunter. Ashly MX-206 8 Seiten. Stereo microphone mixer
Auch für Ashly MX-206: Betriebshandbuch (12 seiten), Technische Hinweise & Spezifikationen (2 seiten), Betriebshandbuch (9 seiten), Betriebshandbuch (12 seiten)
Seite drucken1. INTRODUCTION
Congratulations on your purchase of an Ashly
MX-206 stereo microphone mixer. In one single-space
rack-mount package we have combined the features, reli-
ability, and sonic performance you have come to expect
from Ashly. This third generation mixer adds a universal
100-240VAC 50/60Hz power supply and a 3.5mm front
panel stereo line input jack.
Other features include stereo, mono, and head-
phone outputs, a 20dB input pad on each channel, switch-
able +48V phantom power, up to 60dB of mic preamp gain
(84 dB total), and concentric level and pan controls on
each input channel.
Ultra low-noise summing amplifiers combine the
channel signals for the main outputs. Two 5-segment LED
arrays monitor stereo outputs. Stereo line level outputs
on 1/4" connectors, a transformer isolated 600 ohm mono
output on an XLR connector, and tape/CD inputs and out-
puts on RCA connectors come as standard equipment.
Ashly still uses professional quality 16mm metal shaft po-
tentiometers on all controls for greater accuracy and long
life. Input isolation transformers are not available on the
MX-206.
4. CONTROLS (see next page)
4.1 Input dB (Gain)
This 3-position slide switch sets the operating level of the microphone preamp. Best signal to
noise ratio is obtained with higher gain settings, however it is important to leave enough headroom
(20dB) to prevent clipping. The numbers -20, -40, and -60 refer to the nominal level of the microphone
signal applied to the input. In other words, more gain is needed for a weak -60dB signal than for a
stronger -20dB signal, so as the switch is pushed further to the right, more gain is applied in the mic
preamp circuit. The center position (-40) is a good starting point for most applications. Note: The
Input Gain switch increases or decreases by 20dB increments. To avoid system feedback and possible
driver or hearing damage, turn down the channel level control before adjusting the gain, then slowly
increase level control to suitable setting.
4.2 Input Level
This inner concentric control determines the mix level of its respective channel. If you have
insufficient signal with the level fully turned up, change the Input dB (gain) switch of that channel to
a higher setting (turn down level first).
4.3 Input Pan
This outer concentric control determines the stereo position of the signal.
4.4 Clip
Each input has a red LED which will illuminate when either the mic preamp or input level
circuit pass a signal which is 3dB below clipping. If the level control is turned off and the LED is still
flashing, reduce the Input dB (gain) switch.
Operating Manual - MX-206 Stereo Microphone Mixer
2. UNPACKING
Ashly product is carefully inspected before leaving the
factory to ensure flawless appearance. After unpacking,
please inspect for any physical damage. Save the ship-
ping carton and all packing materials , as they were care-
fully designed to reduce to minimum the possibility of
transportation damage should the unit again require pack-
ing and shipping. In the event that damage has occurred,
immediately notify your dealer so that a written claim to
cover the damages can be initiated.
be forfeited if the carrier is not notified promptly and if
the shipping carton and packing materials are not avail-
able for inspection by the carrier. Save all packing materi-
als until the claim has been settled.
3. AC POWER REQUIREMENTS
to 240 volts AC, 50-60Hz. Use only properly grounded AC
receptacles. To reduce the risk of ground loop hum, use a
central point for system AC power distribution. Power con-
sumption is 30 watts.
As a part of our system of quality control, every
The right to any claim against a public carrier can
The MX-206 mixer will perform normally from 100
3