bluesmart SN Series Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Außenleuchte bluesmart SN Series herunter. bluesmart SN Series 2 Seiten. All in one solar street light

Seite drucken
Installation Height and Distance
Model
Height of pole
SN-50
5-7m
SN-60
6-8m
SN-80
7-9m
SN-100
8-10m
SN-120
9-11m
Packing List
When open the package please confirm that all parts are received, the parts are
listed below:
Components
Quantity
Light body
1pc
Multi-angel bracket buckles
1pc
Rotating Platform
Solar panel
1pc
Bracket support
1pc
M8x100 screw
1set
M8x30 screw
2pcs
Φ
1pc
6mm Allen key
M6x16 screws
6pcs
Φ
5mm Allen key
1pc
4
User Manual
1pc
Remote control
1pc
Humanize Intelligent Remote Control
Technology
Distance between pole
25-28m
28-30m
ON
30-35m
35-40m
TURN ON THE LIGHT
40-45m
T
TIMING CONTROL
U
TIMING+MICROWAVE
Images
Working Modes
ON: Turn on the light
ON
OFF: Turn off the light
OFF
L: 2hrs-100%, 2hrs-70%, 8hrs-20%
L
T: 1hrs-50%, 4hrs-100%, 3hr-50%, 4hr-25%
T
S: 6hrs-100%, 6hrs-50%
s
M: 100% when detect any movement, 30% no movement
M
U: 2hrs-100%, 2hrs-70%, 2hr-50%; sensor start working, when detect
U
movement 50% , 20% no movement.
-20%: decrease 20% brightness based on original working mode
20%
+ 20%: increase 20% brightness based on original working mode
20%
User Manual
Remark:
ON
OFF
L
T
S
M
Supper Brightness
U
20%
20%
The lamp will turn on at night automatically after installation and
*
Solar Street Light Remote
activation, turn off automatically when it receive sunshine.
Default is M mode, you can choose the best mode according to
*
different sunshine condition.
L
OFF
ON
TURN OFF THE LIGHT
LIGHT CONTROL
L
s
M
T
S
Supper Brightness
U
SUPPER BRIGHTNESS
MICRNWAVE CONTROL
20%
20%
20%
Solar Street Light Remote
-20%
+20%
Trouble Shooting
No
Situation
Trouble shooting steps
.
OFF
Check if the solar panel is blocked
from the sunlight by houses, trees
and other obstacles
M
Check if there is any artificial light
source(s) illuminate on the
solar panel at the night
20%
Check the battery have power or
not( There will be a green light
flashing on microwave sensor if
the battery have power)
If all step above have no problem
1
No light at night
Test battery voltage
Test solar panel voltage
Check if the solar panel is blocked
fromthe sunlight by houses, trees
and other obstacles
Check if the surface of the
A serious
solar panelis dusty or covered
2
shortageof
working time
Confirm the working mode is
correct or not
Lighting installation area is a long
time cloudy and rainy days (more
than 5 days)
Check the working mode is corret
or not
Check if the air temperature close
Lights fail to turn
to human body temperature
3
on properly when
humans approach
Check if the installation height is
too high
Solution
Clear obstructions or change installation
location
Remove the artificial light source(s) of
interference or change the installation
location
Put the solar lamp in strong sunshine
charging 4-6 hours,then observe the
lights at night
Disconnect the cable between the
solar panel and lamp, then connect it again,
then press M button working mode, then
wait for 1 min, lamp will be lighting again
If the battery voltage is lower than 11 V, the
battery has been protected automatically.
Please use solar panel charge the battery
directly (do not through solar charge
controller), after full charged, battery voltage
shows 14V or above 14V, then observe the
lighting situation at night
Test solar panel voltage at sunshine.if the
volatge of solar panel lower than 10v,
please replaced damaged battery
Clear obstructions or change installation
location
Clean the surface of solar panels as
detailed above
Use the remote control to readjust the
working mode to M
Under normal circumstances, sunny day
after charging the solar panel to observe
the lights at night
adjust working mode to M or U
when the air temperature us close to
human temperature, motion detection
may slow down. It will return to normal
after the air temperature changes
It is out of motion sensor detection range
when installation height exceeds 10m.
It is recommend to reduce the height or
use other operating modes