aero-naut Canadair CL-415 Instrucciones de construcción - Página 10
Navegue en línea o descargue pdf Instrucciones de construcción para Juguete aero-naut Canadair CL-415. aero-naut Canadair CL-415 13 páginas.
Imprimir página
The model must be balanced laterally on the water. If necessary correct the trim by adding a little lead
ballast to the lighter winglet. It is permissible for the starboard side to be a little heavier, as motor torque
tends to push the left-hand float down towards the water.
Bear in mind the danger of overheating the motors (they only have adequate cooling when in the air), so
do not carry out repeated take-off attempts in rapid sequence. Always take off directly into wind. A breeze
of about 2 - 5 m/sec is advantageous, and very small waves even make take-off easier. The fin acts as a
weathercock, and turns the model into wind.
We hope you have many pleasant flights with your new model, and wish you as many happy landings as
take-offs.
aero-naut Modellbau
Parts List - Canadair CL-415
Part Description
No.
1
Fuselage
2
Wing retainer plate
3
4
Half-former
5
Hardwood undercarriage bearer
6
Half-former
7
8
Guide sleeve
9
Undercarriage wire 1
10
Undercarriage wire 2
11
Undercarriage strut 1
12
Undercarriage strut 2
13
Noseleg unit
14
15
16
Battery support
17
Battery retainer strap
18
Reinforcement
19
Battery support former
20
Snake outer sleeve
21
Servo mount support 1
22
Servo mount support 2
23
Servo plate
24
Hardwood servo rail
25
Snake outer sleeve
26
Wire pushrod
27
Hatch reinforcing strip
28
Hatch cover
29
Hatch latch
30
Hatch support 1
31
Hatch support 2
32
Dowel
33
Main wheel
34
Nosewheel
35
Fin
36
Elevator end-piece
37
Channeled rudder leading edge
38
Rudder hinge lug
39
Control surface horn
40
Tailplane main spar
41
Tailplane secondary spar
42
Tailplane rib
43
Tailplane half-rib
Canadair CL-415
No.
Material
off
1
GRP
4
Plywood
1
Plywood
1
Plywood
1
Lime
2
Plywood
2
Plywood
1
Brass
2
Steel
2
Steel
2
Steel
4
Steel
1
Steel
1
Steel
1
Brass
2
Plastic
2
Aluminium
2
Plywood
4
Plywood
1
Plastic
2
Plywood
2
Plywood
2
Plywood
Lime
2
Plastic
3
Steel
Balsa
1
Plastic
1
Steel / brass
2
Plywood
1
Plywood
Beech
2
Plastic
2
Plastic
1
GRP
Balsa
1
Balsa
3
Aluminium
5
Plated brass
1
Balsa
1
Balsa
12
Balsa
4
Balsa
Size in mm
Ready made
3 mm, die-cut
3 mm, die-cut
3 mm, die-cut
Ready made
3 mm, die-cut
3 mm, die-cut
4 / 3 Ø x 35 mm
3 mm Ø, ready made
3 mm Ø, ready made
2 mm Ø, ready made
2 mm Ø, ready made
3 mm Ø, ready made
3Øx40mm, ready made
Ready made
Ready made
8 x 1 x 130 mm
3 mm, die-cut
3 mm, die-cut
3 / 2 mm Ø, as plan
3 mm, die-cut
3 mm, die-cut
3 mm, die-cut
5 x 5 mm, as plan
2 / 1 mm Ø, as plan
0.6 mm Ø, as plan
5 x 5 mm, as plan
Ready made
Ready made
3 mm, ready made
3 mm, ready made
3 mm Ø, as plan
65 mm Ø, ready made
35 mm Ø, ready made
Ready made
8 x 25 mm, as plan
Ready made
Ready made
Ready made
Ready made
Ready made
2 mm, die-cut
2 mm, die-cut
10