DOMPEL CADEIRA PRIMMA Manual de instrucciones - Página 4
Navegue en línea o descargue pdf Manual de instrucciones para Mobiliario interior DOMPEL CADEIRA PRIMMA. DOMPEL CADEIRA PRIMMA 6 páginas.
Imprimir página
ENGLISH
LOCATION OF INSTALLATION
Install your Dompel product in a level place with no grooves or splices, preventing rocking and vibration. The
location must be airy and it must not allow straight sunlight and it must be away from sources of heat (stoves,
ovens, etc) and flammable products. Do not install your product outdoors.
SECURITY
Avoid accidents. After unpacking the product, keep all the packing material far way from kids.
CLEANING AND MAINTENANCE
Do not use metal spatulas, brushes and cleaning agents such as alcohol, acetone, kerosene, gasoline, bleach,
thinner, solvents, acids, vinegar or other chemicals or abrasives not recommended in this manual. To clean it
easily, it is recommended to use a solution with warm water and neutral soap and after dry carefully. In case of
chemicals reaching the upholstery, clean as soon as possible, preventing products from staining or drying
fabric. Plastic parts can't be washed with boiling water. The chrome-plated metal components can be cleaned
with a soft, dry cloth, and silicone-based automotive wax can be used to increase gloss and durability, in which
case perform the task following the wax manufacturer's instructions. Do periodical cleaning on your equipment,
accumulated dust can affect the beauty of the product.
IMPORTANT
Never drag the product, if necessary, ask other person's help to remove the product from the place. Do not
place containers with high temperature on your product, at the risk of damaging plastic parts or the
upholstery.
INSTALLATION AND ASSEMBLY
ATTENTION! Do not assemble the seat cushion before attaching the screw to the oil pump, otherwise you may
damage the cushion assembling pins (clicks) when removing without need.
Remove all the components from the package and follow the steps below.
MERELY ILLUSTRATIVE IMAGES.
Products may suffer changes in its components without prior warning. If any questions, contact Dompel.
Manually
attach
the chair footbase
(D) on the bottom
of the oil pump
(B).
Insert the hanble (C)
into the oil pump (B)
in the correct position
(as indicated on the
piston label). Fasten
by tightening the side
screws using an
Allen key (4 mm).
Manually insert the
seat cushion (E)
into the seat set
(A) observing the
correct position of
the fasteners
(clicks).
Assemble the footrest
(F2) in the bottom of the
seat set (A). Attach the
04 hexagonal screws M6
x 30 (G), using a spanner
10.
Manually assemble the headrest (J) into the support (H). To adjust the position, simply
pull the handle of the support and move the headrest to the desired position.
Fasten the chair
footbase (D) to the
oil pump (B). Tighten
the washer (M10)
and screw (M10 x
40-SX) using
hexagonal wrench
(M17).
Manually attach the seat
set (A) on the oil pump
rod (B). Assemble the
washer (M10) and screw
(M10 x 40-SX) and
fasten using hexagonal
wrench (M17). To
facilitate the fastening of
the screw, actuate the oil
pump handle (C)
upwards (locking the oil
pump rod turning).
Assemble the footrest
(F1) in the bottom of the
seat set (A) (aluminium
flange). Attach the 04
hexagonal screws
M8 x 35 (G), using a
spanner 13.
Correctly position
the headrest
support (H) and
assemble the seat
set (A). Fasten the
04 allen screws M6
x 30 (I) using an
allen key (4 mm).