American Standard Cadet 3099.203 Características y dimensiones
Navegue en línea o descargue pdf Características y dimensiones para Mobiliario interior American Standard Cadet 3099.203. American Standard Cadet 3099.203 1 páginas. Elongated pressure-assisted toilet
Imprimir páginaCADET™ ELONGATED
PRESSURE-ASSISTED TOILET
❏
2333.100
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Elongated bowl
• Pressure-assisted siphon jet flush action
• Fully-glazed 2" ballpass trapway
• 10" x 12" water surface area
• Side-mounted chrome trip lever
• Close-coupled flushometer tank*
• Speed Connect
tank/bowl coupling system
®
• 2 bolt caps
• 100% factory flush tested
❏
3099.016 Bowl with two bolt caps
❏
4098.100 Tank complete with
coupling components
Nominal Dimensions:
787 x 495 x 737mm
(31" x 19-1/2" x 29")
Fixture only, seat and supply by others
Recommended working pressure range
20 psi - 80 psi
Alternate Configurations Available:
❏
3099.203 Elongated bowl only with slotted
rim for bedpan holding
❏
4098.700 Tank and tank cover only with tank
cover locking device
❏
4098.800 Tank and tank cover only with right
hand trip lever
❏
4098.900 Tank complete with right hand trip
lever and tank cover locking device
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige
❏ Seat: American Standard #5324.019 "Rise and
Shine" (with easy to clean lift-off hinge system)
solid plastic closed front seat with cover.
❏ Seat: American Standard #5311.012 "Laurel"
molded closed front seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate
© 2008 AS America Inc.
❏ Black
Div. of Sloan Valve Co
®
CADET™ ELONGATED
PRESSURE-ASSISTED TOILET
FINISHED WALL
31
(787mm)
3/4 ± 1/4
(19mm ± 6mm)
225mm
(8-7/8)
18-1/2
(470mm)
C/L OF SEAT POST HOLES
5-1/2 (140mm CENTERS)
5/8
(16mm)
13
5-3/4
(330mm)
(146mm)
12
(305mm)
C/L OF OUTLET
NOTES:
THIS COMBINATION IS DESIGNED TO ROUGH-IN AT A MINIMUM DI-
MENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
FOR ADDITIONAL INFORMATION REFER TO INSTALLATION
INSTRUCTIONS SUPPLIED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
M46
VITREOUS CHINA
19-1/2
(495mm)
SUPPLY
AS
REQ'D
14
(356mm)
15
*
8
(381mm)
(203mm)
*
6
(152mm)
FINISHED
FLOOR
9-3/4
(248mm)
Revised 2/08
29
(737mm)