American Standard 2908L Manual de instalación - Página 9

Navegue en línea o descargue pdf Manual de instalación para Bañeras American Standard 2908L. American Standard 2908L 15 páginas. Lifetime / evolution and renaissance whirlpools and bathtubs
También para American Standard 2908L: Manual de instalación y funcionamiento (17 páginas)

American Standard 2908L Manual de instalación
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as needed. Ensure
roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump
and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used
as the primary access opening.
1. Position the whirlpool into the installation opening and level the deck in both directions, shimming the integral support feet IF necessary.
Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).
. Remove the whirlpool and attach a 1 x stringer to the studs, with the top of the stringer touching the traced line.
!
The rim of the bath must not support weight.
3. Install drain components to the whirlpool following the drain installation instructions. Before
replacing your whirlpool for final installation, be certain that an opening has been provided in
the sub-floor for the drain. See the roughing-in drawing and Table 1 for suggested opening
size (shadowed) and location dimensions. The drain/overflow of the bath extends below the
bottom of the bath. Note that this requires a cutout in the floor.
The floor structure beneath the bath must be able to support a total weight of bath, water, and
!
bather. Refer to Table 1 under total weight for your model.
For Models: 2425L/V-LHO, 2425L/V-RHO and 2732L/V;
This bath must be supported along its entire bottom. Use mortar as bedding
material (do not use sand or foam). Apply enough mortar to support the complete
bottom of the bath. After the mortar has been poured, and before it sets, position
whirlpool or bath within recess until the rim is leveled against the leveling stringers (see
"Typical Recess Installation") shown below.
The rim of the bath must not support weight. Allow the mortar material to completely
!
harden before applying weight to the rim or bottom of the bath. Any finish material such
as tile or wall board must be self-supporting if it contacts the deck of the bath.
For Models: 2645L/V, 2771L/V, 6060L/V, 7236L/V, 2422L/V and 2422LA/VA;
Replace whirlpool and re-shim the integral support feet, shimming the entire length of
the support feet. Secure the shims using construction adhesive, silicone, mortar or
equivalent materials. While not a necessity, the use of a foundation base consisting of
cement, mortar, or grout will help provide a solid and secure installation.
The rim of the bath must not support weight. If foundation base is used, allow the
!
bedding material to completely harden before applying weight to the rim or bottom of
the bath. Any finish material such as tile or wall board must be self-supporting if it
contacts the deck of the bath.
TYPICAL RECESS INSTALLATION
C
E
LEVELING
NOTE:
STRINGERS
FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
AMERICAN STANDARD
APRON KIT
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
(EXCEPT 2425 WHERE APRON IS PRIMARY ACCESS OPENING)
FOR E & D DIMENSIONS SEE TABLE 1 ON PAGE 5.
1
(305 mm)
(10 mm)
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON
PUMP/MOTOR END FOR SERVICE.
ACCESS PANELS NOT REQUIRED
FOR BATH TUBS.
TYPICAL PIER TYPE INSTALLATION
AS DESIRED
F
CUTOUT
C
AS DESIRED
MOUNTING
SURFACE
WATERPROOF
SEALANT
BATH
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
FOR G & F DIMENSIONS SEE TABLE 1 ON PAGE 5.
FIGURE 1
TYPICAL INSTALLATION
C
TILE
WALLBOARD
SEALANT
TILE
BATH
BEAD
STRIP
ADHESIVE
LEVELING STRINGER
1 x (not for support)
NOTE: Tile bead kit not included and
must be purchased separately.
G
CUTOUT
(10 mm)
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON PUMP/MOTOR
END FOR SERVICE.
ACCESS PANELS NOT REQUIRED
FOR BATH TUBS.
753737-100 Rev. B
1
(305 mm)