Da-Lite ACOUSTICAL IMAGER Libro de instrucciones - Página 9
Navegue en línea o descargue pdf Libro de instrucciones para Pantalla de proyección Da-Lite ACOUSTICAL IMAGER. Da-Lite ACOUSTICAL IMAGER 13 páginas.
Imprimir página
DOLBY PRO LOGIC* (NON DIGITAL) - LINE LEVEL
Use this installation method for Dolby Pro Logic
applications (not Dolby Digital, DTS or other digital
processing), where the receiver/processor is equipped
with a subwoofer output, or a volume-controlled preamp
(line-) level output:
1. Use RCA-type interconnects to connect the line-
level subwoofer outputs on your receiver or
amplifier to the line-level inputs on the subwoofer.
NOTE: Do not use the LFE input on the subwoofer with
Dolby Pro Logic processors.
NOTE: If your receiver or amplifier only has one subwoofer
output jack, then you will need to use a Y-connector (not
included). Plug the male end of the Y-connector into your
receiver or amplifier's subwoofer output jack, and connect
each of the two female ends to separate RCA-type
interconnects. Finally, plug the RCA-type interconnects into
the line-level inputs on the subwoofer.
2. Connect each speaker to the corresponding
speaker terminals on your receiver or amplifier.
3. Make sure your receiver or processor is correctly
configured to indicate that the subwoofer is "On".
NOTE FOR ADVANCED USERS: If your receiver/processor has
a built-in low-pass crossover filter for the subwoofer output,
you may use the LFE input to bypass the subwoofers internal
crossover.
DOLBY PRO LOGIC* (NON DIGITAL) - SPEAKER LEVEL
Use this installation method for Dolby Pro Logic
applications (not Dolby Digital, DTS or other digital
processing), where the receiver/processor does not
have a subwoofer output, or a volume-controlled
preamp (line-) level output:
1. Connect your receiver or amplifier's front left and
right speaker terminals to the left and right
terminals on the subwoofer that are marked
"Speaker level In". Connect the left and right
terminals on the subwoofer that are marked
"Speaker Level Out" to the corresponding
terminals on the back of your front left and right
speakers.
2. To use the binding-post speaker terminals on the
subwoofer, unscrew the colored collar until the
pass-through hole in the center post is visible
under the collar. Insert the bare end of the wire
through this hole; then screw the collar down until
the connection is tight. The hole in the center of
each collar is intended for use with banana-type
connectors.
3. Connect your receiver or amplifier's center,
surround and surround back speaker terminals to
the corresponding terminals on the back of your
center and surround speakers.
Left Front
–
+
Left
Front
–
+
Left
Surround Back
Surround
Left
–
+
–
Surround Back
Left Surround
Left
–
+
–
SHOWN WITH OPTIONAL 7.1-CHANNEL SYSTEM. FOR STANDARD 5.1 CHANNELS
CONNECT THE SURROUND SPEAKERS TO LEFT AND RIGHT SURROUND
CHANNELS.
Left Front
–
+
OUT
Left Front
–
+
Surround Back
Left Surround
–
+
Surround Back
Left Surround
–
+
SHOWN WITH OPTIONAL 7.1-CHANNEL SYSTEM. FOR STANDARD 5.1
CHANNELS CONNECT THE SURROUND SPEAKERS TO LEFT AND RIGHT
SURROUND CHANNELS.
8
Center
Right Front
–
+
–
Subwoofer
Line-
Level In
L
R
Receiver
Subwoofer
Right
Front
Out
–
+
R
L
–
+
Center
Surround Back
Right
Right
Surround
+
–
+
–
+
Surround Back
Right
+
–
+
Right Front
Center
–
+
–
+
Subwoofer
SPEAKER LEVEL
L
R
+
–
–
+
IN
Receiver
Center
Right Front
–
+
–
+
Surround Back
Right Surround
Left
Right
–
+
–
+
–
+
Surround Back
Right Surround
Left
Right
–
+
–
+
–
+
+
Right Surround
–
+