Da-Lite ADVANTAGE ELECTROL Libro de instrucciones - Página 5

Navegue en línea o descargue pdf Libro de instrucciones para Pantalla de proyección Da-Lite ADVANTAGE ELECTROL. Da-Lite ADVANTAGE ELECTROL 12 páginas. Tensioned large
También para Da-Lite ADVANTAGE ELECTROL: Libro de instrucciones (12 páginas), Manual del instalador (2 páginas), Libro de instrucciones (4 páginas), Libro de instrucciones (12 páginas), Libro de instrucciones (16 páginas)

Imprimir página

Da-Lite ADVANTAGE ELECTROL Libro de instrucciones

SCREEN ADJUSTMENT FOR 120V SCREENS

If your Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller

assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the

120V Wiring Diagram

1. Locate the wall switch and remove the cover plate from the

wall switch and remove the switch from the junction box.

2. Locate the two tactile buttons on the back of the switch.

They are black round buttons on silver plates. See 120V

Wiring Diagram.

3. To adjust the down limit switch, press and hold the down

tactile button until the LED on the back of the switch turns

solid red. This will put the motor in limit set mode. Turn the

wall switch over and use the down button on the front of the

switch. Press and hold the down button until the desired

down position is reached. If you travel too far down, press

the up button to move the screen upward. If you press and

let go of either the up or down buttons, the motor will do a

small jog in that direction for fine adjustment of the screen.

Once the desired position is reached, turn the switch over;

press and hold the down tactile button until the LED on back

of switch blinks red twice. The down limit is now set.

NOTE: If the screen is in limit set mode and no buttons are

pushed for 20 seconds, the LED on the back of the wall

switch will turn off, the motor will return to run mode and no

changes will be saved. If this occurs, return to step 3 for

down limit adjustment or step 4 for up limit adjustment.

SCREEN ADJUSTMENT FOR 220V/240V SCREENS

1. Remove the cover plate from the 3-button wall switch and

remove the switch from the junction box.

2. Locate small 3-position switch on back of wall switch. See

Figure 5 for 120V screens or Figure 8 for 220/240V screens.

3. To adjust the down limit switch, slide the 3-position switch to

the down position. Press and hold the down button to run

the screen down to the desired stop position. Release the

button to stop the screen. DO NOT PUSH THE STOP

BUTTON.

4. When the screen is in the desired down position, slide the

3-position switch to the off (center) position. The down limit

switch is now set.

5. To adjust the up limit switch, slide the 3-position switch to

the up position. Press and hold the up button to run the

screen up to the desired stop position. Release the button to

stop the screen. DO NOT PUSH THE STOP BUTTON.

6. When the screen is in the desired up position, slide the

3-position switch to the off (center) position. The up limit

switch is now set.

4. To adjust the up limit switch, press and hold the up tactile

button until the LED on the back of the switch turns solid

green. This will put the motor in limit set mode. Turn the wall

switch over and use the up button on the front of the switch.

Press and hold the up button until the desired up position is

reached. If you travel too far up, press the down button to

move the screen downward. If you press and let go of either

the up or down buttons, the motor will do a small jog in that

direction for fine adjustment of the screen. Once the desired

position is reached, turn the switch over; press and hold the

up tactile button until the LED on back of switch blinks green

twice. The up limit is now set.

5. To test the limit switch settings, press and release the up or

down buttons on the switch to operate the screen.

6. Replace the switch and cover plate on the wall.

IMPORTANT NOTE: The wall switch is REQUIRED to make

any limit switch adjustments, even if a third party control

system is used. Therefore, it is advised to wire the switch or

provide a 3-conductor connection that is accessible.

CAUTION: DO NOT ADJUST FOR MORE DROP THAN

WHAT WAS ORDERED. AT LEAST 1–1/2 WRAPS OF

FABRIC MUST REMAIN ON THE ROLLER. THIS SCREEN

COMES STANDARD WITH 0" OR 2" BLACK AT THE TOP.

SEE THE SPECIFICATION DATA SHEET FOR DETAILS.

7. To test limit switch setting, make sure the 3-position switch

is in the off (center) position. Press and release the up or

down button on the wall switch to operate the screen.

8. Replace switch and cover plate on the wall.

NOTE: If stop button is pressed, the wall switch will reverse

direction. To correct this, press the stop button again. This

will reset the switch. You will have to re-set both the up and

the down limit settings.