Da-Lite HORIZON ELECTROL Libro de instrucciones - Página 2

Navegue en línea o descargue pdf Libro de instrucciones para Pantalla de proyección Da-Lite HORIZON ELECTROL. Da-Lite HORIZON ELECTROL 8 páginas.
También para Da-Lite HORIZON ELECTROL: Libro de instrucciones (8 páginas)

Imprimir página

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:
1.
Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.

Pre-Installation

1.
Carefully unpack screen and remove outer wrapping
from case.
Drywall Screw
Access Panel
Machine Screw
Truss Head Screw
Shipping Bracket
Installation
1.
Install screen by raising unit into position between joists at one
end only. Install one lag screw in each mounting bracket.
2. Level unit lengthwise with a carpenter's level and plumb level.
Secure opposite end.
3. Detach access panel by removing screws (Figure 1).
CAUTION! Do not seal in until screen has been secured in
position and properly tested for satisfactory operation.
ATTENTION! Ne fixez pas l'écran jusqu'à ce qu'il ait été
correctement mis en place et qu'il fonctionne
convenablement.
4. Remove the two screws holding the splitter junction box (Figure 2).
5. Unwrap the supplied 25 ft. RJ-14 cord. Plug one end into a QEYE
port on the primary splitter (see wiring diagram).
6. Run the 25 ft. RJ-14 card to the back of the wall keypad and plug
into the RJ receptacle.
7.
Remove the two screws holding the junction box cover plate.
Install the electrical hookup (see wiring diagram).
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
8. After the electrical connections are completed, replace the
junction box cover plate.
2
Hex Head Screw
Figure 1
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of fire, electric shock, or injury to
persons.
Save These Instructions
2. Make sure to recheck measurements of screen location
before installation.
Junction Box
Splitter
Junction
Screen
Box
Motor
Slats
9. Carefully remove tape strips securing picture surface around roller.
CAUTION! Do not cut tape on fabric with knife or any sharp
tool. Pull orange string.
ATTENTION! Ne coupez pas le ruban adhésif sur la toile avec
un couteau ou un outil tranchant. Tirez sur le cordon orange.
10. Carefully remove wood boards securing mask surface to case.
11. Test installation by carefully running picture surface and mask
surfaces up and down several times. Be prepared to stop the
screen. IMPORTANT: Read operating instructions before
testing screen.
NOTE: When rolled down, the picture surface should wrap fully
around the roller. No part of the roller should be exposed. Picture
surface and mask surfaces will automatically stop in the down
position.
CAUTION! Excessive continuous operation may cause
overheating. If this happens, the motors will shut off until they
cool to a normal operating temperature. Duty Cycle of screen
is 1 Min. ON / 3 Min Off.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchauffe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la température
normale de fonctionnement. Le cycle de fonctionnement est
de 1 min. en marche / 3 min. à l'arrêt.
Mask
Motor
Mask Surface
Tape Strips
Picture Surface
Figure 2