American Standard Town Square 2817 Instrucciones de instalación Cuidado y mantenimiento
Navegue en línea o descargue pdf Instrucciones de instalación Cuidado y mantenimiento para Aseos American Standard Town Square 2817. American Standard Town Square 2817 4 páginas.
Imprimir página
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Town Square 1.6 gpf / 6 Lpf 2-piece Toilet
Town Square 1.28 gpf / 4.8 Lpf 2-piece Toilet
Model 2817 - Elongated, Right Height
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
7-1/2"
(191mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
(470mm)
8-1/2"
14-5/8"
(217mm)
(373mm)
12"
(305mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
3
between wall and toilet is limited to 3-1/2". In this case, check your supply and hose dimensions.
CLOSET
FLANGE
A
CLOSET
BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn
90 ° , and slide into place 6" (152 mm)
apart and parallel to wall.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 0
Adjustable Wrench
Flexible Supply Tube
29-3/4"
(756mm)
18-1/2"
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
16-1/2"
(419mm)
8"
(204mm)
5-1/2"
(140mm)
FINISHED
FLOOR
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly
around waste flange (horn), with
tapered end of ring facing toilet. Apply a
thin bead of sealant around toilet base.
™
with Seat
15-1/4"
(390mm)
14"
(356mm)
31-1/8"
(791mm)
2-1/4"
(57mm)
BACK VIEW
6"
(for reference)
(152mm)
12-3/4"
(326mm)
WAX RING
Sealant
Tape Measure
Closet Bolts
Carpenters Level
IMPORTANT: Water supply on
the wall is required at 2-1/4" or
8" from centerline of the toilet
(see rough-in). First suggested
position is hidden behind the
toilet. The geometry of the toilet
gives space for this installation.
The second suggested position
is next to the toilet. Between
these two positions, the space
for the supply between wall and
toilet is limited to 3-1/2". In this
case, check your supply and
hose dimensions.
5
FLANGE
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
Certified by
IAPMO R&T
NUT
TAPERED
WASHER
CLOSET
BOLT
7 30 1 45 6 - 1 0 0 R e v. A