Ekinex EK-GD1-TP-4-HV Manual de instalación - Página 3

Navegue en línea o descargue pdf Manual de instalación para Regulador de intensidad Ekinex EK-GD1-TP-4-HV. Ekinex EK-GD1-TP-4-HV 6 páginas. Vac 4-channel phase cut dimmers

Imprimir página

KNX bus line connection

The connection to the bus network takes place via the

KNX terminal included in the delivery and inserted in the

special housing located on the front of the device in the

upper part.

Characteristics of the KNX terminal block

• spring clamping of conductors

• 4 seats for conductors for each polarity

• terminal suitable for KNX bus cable with single-wire

conductors and diameter between 0.6 and 0.8 mm

• recommended wire stripping approx. 5 mm

• color codification: red = + (positive) bus conductor,

black = − (negative) bus conductor

Warning! To power the KNX bus lines, use exclusi-

vely KNX bus power supplies (e.g. ekinex EK-AB1-

TP, EK-AG1-TP or EK-AM1-TP). The use of other

power devices can compromise communication

and damage the devices connected to the bus.

Connection of loads and power supply

The connection to the 90-230 Vac 50-60Hz power supply

is done via the spring terminals located in the lower part

of the device.

Characteristics of the supply and loads terminal block

• Spring tightening of the conductors

• Power and loads wiring: 1.5 mm

ded – 16 - 13 AWG

• Stripping recommended approx.: 5.0 - 6.0 mm

Warning! The electrical connection of the appliance

must be carried out exclusively by qualified person-

nel. Incorrect installation can cause electrocution or

fire. Before making the electrical connections, make

sure you have deactivated the mains voltage.

Outputs

The cables connected to the outputs must be correctly

sized and must be isolated from any wiring or parts with

different voltages. The length and type of connection ca-

bles must comply with the regulations in force.

Configuration and commissioning

The configuration and commissioning of the device re-

quires the use of the ETS® (Engineering Tool Software)

V5 program or later versions. These activities must be

carried out in accordance with the design of the building

automation system created by a qualified professional.

To configure the device parameters, the corresponding

application program or the entire ekinex® product data-

base must be loaded into the ETS® program. For detailed

information on the configuration possibilities, consult the

application manual of the appliance available on the web-

site www.ekinex.com.

solid – 2.5 mm

stran-

INSTALLATION TECHNICAL NOTES

• Installation and maintenance must be

performed only if the power supply has

been turned off.

• Installation and maintenance must only

be performed by qualified personnel in

compliance with current regulations.

• The product must be installed inside

a wall mounting box or an electrical pa-

nel, where it is recommended to install a

surge protector.

• The product must be protected by a sui-

tably sized fuse.

• The product must be protected by a su-

itably sized magnetothermic switch on

the main input line.

• The product must be installed in a verti-

cal position with the front / label facing

the front or in a horizontal position with

the front / label facing upwards. Other

product installation positions are not

allowed.

• Do not connect inductive loads.

• Do not connect to UPS (uninter-

ruptible

power

tput

other

than

The device is not grounded. Protection

from accidental contacts is guaranteed

by the casing.

• Use in thermally harsh environments

could limit the output power.

• In the system, keep the 90-230Vac circu-

its and the non-SELV circuits separate

from the SELV circuits at very low safety

voltage and from the KNX bus

• It is absolutely forbidden to connect, for

any reason whatsoever, directly or indi-

rectly, the 90-230Vac mains voltage to

the KNX bus or to the loads.

• Use double insulated cables.

supply)

with

ou-

Pure

Sine

Wave.