Ekinex EK-E12-TP-RW-NF Ficha de datos - Página 2

Navegue en línea o descargue pdf Ficha de datos para Interruptor Ekinex EK-E12-TP-RW-NF. Ekinex EK-E12-TP-RW-NF 5 páginas. Pushbutton
También para Ekinex EK-E12-TP-RW-NF: Manual de inicio rápido (9 páginas)

Imprimir página

Completion of the pushbutton

The pushbutton is completed through a separate order of:

• a set of rockers that allows the use as a 1-fold, 2-fold

or 4-fold pushbutton;

• a 1-fold plate (square, EK-PQS-...) or a 2-fold plate

(rectangular, EK-P2G-... or EK-P2S-...) in combination

with another bus device of 71 Serie or a 55 x 55 mm

ﬂ ush-mounting insert;

• a square frame of the ekinex

for the 'NF - No Frame versions).

Rockers

Three-positions rockers with central neutral position have

to be mounted on the pushbutton. Pushing one side of

a rocker (for example the upper one), the pushbutton

sends on the bus a telegram for switching on, increasing

the brightness of luminaires or raising the blinds, while

pushing the other side (for example the lower one), it sen-

ds a telegram for switching oﬀ , reducing the brightness of

luminaires or lowering the blinds. Each channel is equip-

ped with LEDs which can be freely programmed as status

feedbacks of the loads and as orientation nightlight.

Code set of

Appea-

Nr. and type of

rockers *

rance

EK-T1Q-xxx

EK-T2R-xxx

EK-T4Q-xxx

EK-T4R-xxx

(*) To be completed with the extension for the colour: xxx = MAA (white), xxx = GAG

(silver), xxx = MAL (black)

Plate

The pushbutton may be completed by a square 1-fold pla-

te or by a rectangular 2-fold plate. In both cases the plate

must be necessarily provided with a 60 x 60 mm window

for the mounting of the device.

Plate

Type

Appearance

code *

EK-PQS-...

1-fold **

EK-P2G-...

2-fold ***

EK-P2S-...

2-fold ***

(*) To be completed with the extension for colour, material and ﬁ nishing

(**) For mounting without frame ('NF) it requires the EK-TAQ adapter

(***) For mounting without frame ('NF) it requires the EK-A71-... adapter

Frame

The pushbutton can be completed by a square 1-fold fra-

me or by a rectangular 2-fold frame of the ﬂ ank or form

series. The 'NF (No Frame) versions of the pushbutton do

not require any frame.

form or ﬂ ank series (not

Modularity

rockers

[mm]

1 square

60 x 60

2 rectangular

30 x 60

4 square

30 x 30

4 rectangular

60 x 15

Window modula-

rity [mm]

60 x 60

55 x 55 (1)

60 x 60 (1)

60 x 60 (2)

Mounting

The device has degree of protection IP20, and is there-

fore suitable for use in dry interior rooms. The installation

of the device diﬀ ers depending on the mounting with or

without frame ('NF series).

Mounting with frame

Carry out the following steps:

• ﬁ x the metallic support (h) with the pair of screws (g) on

the ﬂ ush-mounting box (i) equipped with ﬁ xing holes at

60 mm distance;

• press for ﬁ xing the pushbutton (d) on the adapter (e);

• insert pushbutton and adapter (d+e) in the metallic sup-

port (h). Mounting the device follow also the indication

TOP (arrow tip pointing up) on the rear side of the de-

vice;

• snap a square frame (f) of the form or ﬂ ank series, in-

serting it from the rear of the pushbutton (d);

• enter the bus terminal block, previously connected to

the bus cable in its slot on the rear side (see also: "Con-

nection of the KNX bus line"). At this point it is recom-

mended to carry out the commissioning of the device

(see also "Conﬁ guration and commissioning") or at le-

ast the download of the physical address;

• fasten the device on the metallic support supplied with

the pair of screws (c);

• snap the rockers (b) for the operation of the device;

• snap the plate (a).

Mounting with frame

a) 1-fold plate

b) Rockers

c) Fixing screws (for device)

d) Device (pushbutton 71 Serie)

e) Adapter for mounting with frame (included in the delivery)

f) Frame (square, form or ﬂ ank series)

g) Fixing screws (for metallic support)

h) Metallic mounting support

i) Flush-mounting box

Mounting without frame ('NF series)

Carry out the following steps:

• insert the metallic support (f) on the adapter (g);

• ﬁ x adapter and support (f+g) with the pair of screws

(e) on the ﬂ ush-mounting box (h) equipped with ﬁ xing

holes at 60 mm distance;