American Time SiteSync IQ Manual de instalación de inicio rápido - Página 2

Navegue en línea o descargue pdf Manual de instalación de inicio rápido para Accesorios American Time SiteSync IQ. American Time SiteSync IQ 2 páginas. Wireless system controller with standard gps & magnetic mount tx antenna
También para American Time SiteSync IQ: Manual de instalación de inicio rápido (2 páginas), Manual de instalación y funcionamiento (2 páginas), Manual de instalación y funcionamiento (13 páginas), Manual de instalación y funcionamiento (7 páginas), Manual de instalación y funcionamiento (6 páginas), Manual de instalación de inicio rápido (2 páginas), Manual de instalación de inicio rápido (2 páginas), Manual de instalación de inicio rápido (2 páginas), Manual de instalación de inicio rápido (2 páginas), Manual de instalación de inicio rápido (2 páginas), Manual de inicio rápido (2 páginas), Manual de inicio rápido (2 páginas), Manual de inicio rápido (2 páginas)

American Time SiteSync IQ Manual de instalación de inicio rápido
QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• GPS receiver with 15' cable and mounting bracket
• Power supply
(B)
• Campus TX antenna kit
(C)
• 9 pin data cable
(D)
• External Transmitter and power cord
• Installation and Operation Manual
3
Choose your location
• Choose a location for the GPS receiver outside, mounted
parallel to the horizon, with a clear view of the sky and the
label facing up. The included mounting bracket allows for
mounting on the side of a building or other structure.
Avoid high voltage equipment and excessive roof overhang
when choosing a location.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
System controller
located high & central
TX Ant signal
out to clocks
GPS signal in
4
Connect cables to the system controller
A.
Connect the GPS antenna to the STD GPS RJ45 port.
• If desired for a redundant connection to the time server,
connect a CAT5 or higher Ethernet cable to the Ethernet port.
Refer to the SiteSync IQ Installation & Operation Manual for
detailed instructions on using multiple time sync methods.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect campus antenna to ANTENNA port on the External
Transmitter. *Lightning arrestor must be grounded per local
(A)
electrical code.
D.
Connect the 9 pin data cable to the DATA port on the External
Transmitter.
Connect the 9 pin data cable to the EXT TX port on the
(E)
system controller
E.
Connect the External Transmitter power cord to the POWER
External
Transmitter
SITESYNC IQ
INPUT port on that unit.
Plug 120V cords for both units into
power source. Turn the POWER SWITCH
on the back of the system controller and
external transmitter to the on position.
*
See above
To ground
System Controller
B
D
A
POWER INPUT
ANTENNA
DATA
D
E
C
To local
power
(120VAC)
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
(Page 9 in Installation Manual)
2. Create a 4 digit User Lock or enter 0000 to disable this
feature. Press
.
Tip: Record this password.
O
3. Create a 4 digit Service Lock (for advanced features) or enter
0000 to disable this feature. Press
O
Tip: Record this password.
4. Select local time zone by using the
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from.
5. Press
to select automatic DST (Daylight Saving Time) or
8
to disable DST if your location doesn't observe DST.
0
Press
O
6. Press
for 12-hour mode - AM/PM (1:00PM).
1
Press
for 24-hour mode - Military (13:00).
2
7. To confirm proper set up, press
to sync.
8
• If successful, "GPS Sync Successful" will display
• If not successful, "GPS Sync Failed" will display. Re-try
by pressing
again.
8
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
MON MAR 14 2016
10:38:06 AM USCT
American Timel
Status=AUTO
GPS=Y
.
keys. Press
.
<>
O
Note: Screen
will advance
immediately
TX