DoorKing 1175 Manuales básicos de inicio rápido

Navegue en línea o descargue pdf Manuales básicos de inicio rápido para Abrepuertas DoorKing 1175. DoorKing 1175 2 páginas. For overhead gate/door up to 14 feet high and 25 feet wide

Imprimir página

QUICKSTART "BASIC" GUIDELINES FOR MODEL 1175 - FOR OVERHEAD GATE/DOOR UP TO 14 FEET HIGH AND 25 FEET WIDE

Assemble Operator

Secure rails to powerhead assembly

with 4 bolts, nuts and lock washers.

Chain must not rub on steel rail separators.

Route chain around gear reducer's

sprocket and through unlocked

carriage assembly. Connect

chain together with double

master link.

Double Master Chain Link

Chain Tension Adjustment

Always adjust both sides of rails evenly.

Header

Bracket

Mount Operator

Install the gate/door bracket "centered" on the top rail of the gate/door by bolting or welding. Center the header bracket

above the top of the gate/door bracket a minimum of 2.5 inches from the bottom of the header bracket. Check the gate/door's

opening swing path, some gate/doors will swing open higher than the bottom of the

header and could hit the rails if they are mounted too low. Mount header bracket with

Header

Header Bracket

lag bolts, anchor sleeves or welding to header.

IF the operator is installed less than 8 feet

2.5" Minimum

above the floor, then operator's exposed moving

parts must be covered. DoorKing offers a cover

Gate/Door Bracket

for protection, Sold separately, P/N 1175-020

If a ceiling extension bracket is needed, it must be

fabricated (2" wide L angle steel is recommended).

Chain tension adjustment. Adjust

equally on both sides of rails.

Do not let chain rub against steel rail separators.

Carriage Assembly

Connect the arms together with 2 bolts,

then connect them to the carriage assembly

and gate/door bracket.

Install Breather Cap on Gearbox

i n

C h a

c k e t

Fill Mark

S p r o

Install breather cap after operator has been mounted. Check

oil level, use Mobil SHC-629 synthetic gear oil or equivalent.

IMPORTANT:

Do not overfill.

THIS PRODUCT IS FOR INDOOR USE ONLY.

Install in a protected area NOT exposed to weather.

Sprocket

Manual Release

Unlock,

Pull and

CAUTION

Turn Ring

FRAGILE POWERHEAD!

Ceiling

Install the powerhead with lag bolts or anchor

sleeves. Rails must be mounted level!

Gearbox should be filled to fill mark only.

Model 1175 is intended for installation only on overhead gate/door used for vehicles.

Pedestrians must be supplied with a separate access opening.

For safety and installation instructions, please refer to the owner's manual.

IMPORTANT:

The carriage assembly's spring

loaded chain catch will only lock into place

in the double master chain link.

Limit Switches

Push and hold locking plate tab to

adjust limit nuts at full open and

full close gate/door positions.

PUSH TO OPERATE

technician use only

Open

Limit

Nut

Push and Hold Tab

FIRE

EXIT

9410

LOOP

SW1

2 3 4

POWER

TIME

DELAY

REV SENSE

SECONDARY

PRIMARY

REVERSE

LOOP

9410

4405-018

Neutral (White)

Hot (Black)

Chassis Ground

High Voltage

(Rigid Conduit)

ON/OFF

Alarm

Loop (Flexible Dry Conduit)

Reset

Switch

Limit

Nut

1477-010

Alarm

120 S. Glasgow Avenue

Inglewood, California 90301

U.S.A.

Board Adjustments

After DIP-switches are changed, power must be

shut-off, and turned back on for new settings.

SW1

SW 2

1. OFF

2. OFF

ON-Auto Close Timer

4. OFF

5. OFF

6. OFF

See reverse side

7. OFF

8. OFF

Auto Close Timer

When SW1, switch 4 is turned ON,

automatic timer can be set from 1-23

seconds to automatically close gate/door.

115 VAC Connection

DANGER

OPERATOR MUST BE

PROPERLY GROUNDED!!

HIGH VOLTAGE!

Tip: It is recommended that a surge suppressor be

installed on the high voltage power lines.

Set Reverse Sensor

REV SENSE

Clockwise INCREASES

SECONDARY

PRIMARY

Secondary

the reverse sensitivity.

reverse sensor

Counter-clockwise

is NOT used.

DECREASES the reverse

Min Max

sensitivity.

Sensitivity

Entrapment Protection

Installation of ONE MONITORED external

entrapment protection device MUST be

installed in the DOWN direction or operator

WILL NOT function.

See reverse side

Opening Devices

Radio Receiver Not included - Refer to a specific Radio

Receiver Manual (available from www.doorking.com)

for more information on radio receivers and antenna

installation. (See reverse side for wiring)

3-Button Control Station Not included - Refer to manual

for specific installation and included warning label

placement. (See reverse side for wiring)

Loop Detectors

Not included - Refer to the Owner's manual and

Loop Information Manual (available from

www.doorking.com) for more information on

loops and loop detectors.

1175-066-F-2-19