DACE LUX DC12 Manual de instalación y uso - Página 2

Navegue en línea o descargue pdf Manual de instalación y uso para Abrepuertas de garaje DACE LUX DC12. DACE LUX DC12 12 páginas.

Imprimir página

Table of Contents

1.0

Foreword

2.0

Disclaimer

3.0

Glossary

4.0

Technical Speciﬁca ons

5.0

Parts Iden ﬁca on

6.0

Assembling and Installing the Operator

5.1

Ver cal Mount Roll Up Drive Channel Posi on

5.2

A aching the Power Head to the Drive Channel

5.3

A aching the Cross Tube to the Drive Channel

5.4

Moun ng the Floa ng Bracket to the wall

5.5

A aching Door U-Brackets

5.6

Securing the Drive Channel to the Floor

5.7

Posi oning & Securing the Ba ery

7.0

Informa on before programming and commissioning the operator

8.0

Se ng the Physical Open & Close Limits

9.0

Programming the Operator

9.1

Programming Menu

9.2

Se ng the Open & Close Limits

9.3

Se ng the Opening & Closing Force

9.4

Enable or Disable Safety Beams

9.5

Se ng Auto Close

9.6

Se ng the Auxiliary Output

9.7

Enable or Disable Electric/Magne c Lock

9.8

Programming Remotes

9.8.1

Programming a Remote Bu on to Trigger the Operator

9.8.2

Programming a Remote Bu on to Turn the Operator Light On & Oﬀ

9.8.3

Erasing a Single Remote and its Bu ons from the Operator

9.8.4

Erasing All Remotes and their Bu ons from the Operator

9.8.5

Programming a Remote Bu on to set the Holiday Lockout feature

9.8.6

Factory Reset

10.

Advanced Controller Programming Op ons

10.1

Control Board Layout

10.2

External Trigger

10.3

Safety Beams

10.4

Electric and Magne c Locks

10.5

Auxiliary Status Output

10.6

Auxiliary Low Ba ery Output

10.7

Auxiliary Trigger Output

10.8

Auxiliary Light

11.

Connec ng a Solar Panel

12.

Error Codes

13.

Warranty

Page

ERROR

MEANING

CODE

Beams Blocked

Lockout

Encoder Stop

(Fault/Obstruc on)

Error Programming

Remote

Heavy Load

Check Balance

CAUSE & REMEDY

Cause:

The infrared beam between the two Safety Beam sensors are blocked, indica ng

an obstruc on or the ba eries in the transmi er beam are low.

Remedy:

Remove anything that may be obstruc ng the doorway.

If there is no obstruc on, check that the Beam's wiring is correct.

Test the beams to ensure they are in fact opera onal.

Check for possible ant infesta ons in the beams.

If no beams have been installed, ensure that the beams se ng in the operator

menu is set to

Cause:

The operator has been placed in 'Holiday Lockout' mode.

Remedy:

To deac vate Holiday Lockout, press the bu on on the remote that was assigned

to ac vate Holiday Lockout.

To prevent accidental ac va on, is it recommended that the func on is assigned

to a remote/s by pressing two of the remote bu ons simultaneously. This will

reduce the risk of accidentally ac va ng the Lockout func on.

Cause:

The operator has 'stalled'. This could be as a result of the door hi ng an

obstruc on, the limits being set incorrectly, an incorrect force limit se ng or a

faulty Encoder.

Remedy:

1) Remove any physical obstruc on. If no obstruc on....2.

2) Check that the limits have been set correctly and that the door is not stopping

hard against the ﬂoor or any other physical stop. If the limits are set

correctly.....3.

3) Check the Door Balance. To do this, disengage the door from the Drive

Channel via the Manual Release Mechanism. Be sure to support the door

before doing so to ensure that the door does not drop a er being released.

Manually open and close the door. The door should open and close easily,

requiring the same amount of force in both direc ons. If the door is diﬃcult to

move in either or both direc ons, and the open and closing forces are not

within the opera ng parameters, the door will need to be balanced and

serviced. If the Door Balance is correct.....4.

4) The Force Level se ngs on the Control Board may need to be adjusted. This

may happen if the door is ageing.

5) If all the previous checks are in order the Encoder may be faulty and the

garage operator will need to be serviced.

Cause:

All 64 remote slots are occupied.

Remedy:

No further remotes can be programmed to the controller. In order to add new

remotes it will be necessary to delete some to make space.

Cause:

The operator has detected that the li ing force is greater than the allowed

maximum. This could be as a result of an increase in the door's fric on, incorrect

door specs or possibly a broken door spring.

Remedy:

Cau on: This error message indicates that the door is too heavy and that the

operator is unable to li it. Disengaging the the door from the Drive Channel via

the Manual Release Mechanism could result in the door dropping fast and could

cause damage or injury!

Disengage the door slowly and with great cau on. Manually open and closed the

door to establish the weight. If it is diﬃcult to li , the door will need to be

repaired before reconnec ng it to the operator.

Cause:

The door has gone out of balance, usually as a result of either one or both of the

door torsion springs being broken.

Remedy:

Disconnect the door from the operator and open and close it manually. If moving

the door in one direc on is more diﬃcult than the other direc on then the door

will need to be repaired before reconnec ng it to the operator.