AmerTac BL-BR33B-SW Manual del usuario
Navegue en línea o descargue pdf Manual del usuario para Luminaria AmerTac BL-BR33B-SW. AmerTac BL-BR33B-SW 2 páginas. Remote controlled led rgbw under cabinet light
Imprimir páginaBL-BR33RGB-SW Owner's Manual
Location of Controls
1. ON/COLOR/OFF Switch
2. 6 Super Bright LEDs
3. Battery Compartment*
4. Magnets*
5. Slide Brackets*
6. Metal Plates*
7. 3M Adhesive Pads*
OPERATE AND CONTROL THE LIGHT TWO WAYS:
ON/OFF Switch – Once batteries are installed:
Press to turn the light ON WHITE, then again for RED,
again for GREEN, again for BLUE, again for OFF.
REMOTE CONTROL OPERATING – (On First Use, Remove Battery Compartment Protective Plastic)
The remote control unit will operate Under Cabinet Light in 65-82 feet (20-24 m) range. Once
batteries are installed, turn light ON by pointing the remote control towards the light. Use the
DIMMER, and TIMER functions by pointing the remote control towards the light and selecting the
desired function.
REMOTE CONTROL – Controls Aluminum Under Cabinet Light.
POWER - Controls Aluminum Under Cabinet Light
Turns light ON
Turns light OFF
DIMMER - Controls brightness of light
Press and hold (+) increases brightness
Press and hold (-) decreases brightness
COLOR - Chose color of LEDs
Pick WHITE, RED, GREEN or BLUE directly from the remote control. The light will remember your
color choice if you power ON again using the remote. If you power ON directly from the light, it
will always start with WHITE.
Controls the amount of time the Under Cabinet Light stay ON.
TIMER – Turn lights ON fi rst, select duration. Light will fl ash once to confi rm command. Timer
clears when light turn OFF. 15, 30, 60 and 120 minutes preset.
ADDING UNDER CABINET LIGHTS TO A SET
Up to 20 lights may be controlled by one remote control. No programming is needed. Any similar
lights will be controlled when placed within the range of the remote control's signal.
MOUNTING INSTRUCTIONS
Magnetic Mounting (preferred)
The magnetic sections on the back of the light can be adjusted left to right so the corresponding
metal plates can be placed in the most ideal location for your installation.
Magnet option 1 - The metal plates come pre-drilled for easy front mounting on the desired
surface with included screws. Attached the fi rst plate to the overheads surface and check
location of second to make sure that sliding magnet will adhere to it.
Magnet option 2 - Remove protective cover from one side of the double-sided adhesive pad.
Place in center of the metal mounting plate. Do this for both metal-mounting plates. Place the
metal mounting plate with the adhesive pad onto the magnets located on the back side of
the light. Adhesive side placed away from the product (so it can stick into mounting position).
Do this for both metal-mounting plates. Remove second protective cover from adhesive tape
and place against desired surface. The metal mounting plate should be adhered to the desired
surface.
This is permanent tape that may cause damage if removed. Not recommended for use on
wallpaper or delicate surfaces.
Pulling on the light after the plates are properly installed should disconnect the metal mounting
plate from the magnets to allow for changing of batteries. The light should easily be able t o re
attached as the magnets and plates will draw to each other.
If you plan on using the light on a metal/magnetic surface, such as a cabinet, you may not need
to install the plates at all
Screw Mounting (optional)
1. Remove 2 metal plates & 2 3M Adhesive tapes from the 2 magnets on the back of the light.
2. Use Wall Anchors (not included) if securing to dry wall.
3. Measure two holes 6.75" (171 mm) apart. Drill two holes into mounting surface, insert wall
anchors (not included) and insert screws.
4. Leave screw heads out slightly so they can be inserted into the mounting holes located on
the back of the light.
5. Align and insert screw heads into mounting holes. Once inserted, slide the light onto the
screw heads to secure its position.
Product Dimensions:
Under Cabinet Light Size - 13.375" (H) x 2.25"(W) x 0.75"(D) / (340 mm x 56 mm x 19.3 mm)
Remote Size - 3.375" (H) x 1.5"(W) x 0.25"(D) / (86 mm x 40 mm x 6 mm)
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
8. Remote Control
9. ON/OFF Switch
10. Dimmer
11. Color Selector
12. Timer
13. Battery Compartment
*On back of unit
REMOTE CONTROLLED
LED RGBW UNDER CABINET LIGHT
INDOOR, DRY USE ONLY
BATTERY
--Each Under Cabinet Light requires 3 AA batteries (not included).
-- Remote Control requires CR2025 battery (Included)
Insert/Replacing the batteries
UNDER CABINET LIGHT – 3 AA batteries
If the LEDs appear to be dim this is an indication that the batteries need to be replaced.
- Slide off the battery compartment.
- Remove old batteries if replacing batteries.
- Insert three new AA batteries.
- Make sure to follow battery polarity guide when installing new batteries.
- Replace battery compartment housing.
REMOTE CONTROL – CR2025 battery pre-installed.
- Grip and slide battery drawer out
- Remove battery.
- Place new battery in position aligning polarity (+) (-) as indicated.
- Slide battery drawer in.
This product contains a button cell. If swallowed, it could cause severe injury or death in just 2
hours. Seek medical attention immediately.
SAFETY INFORMATION
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: Modifi cations to this product will void the user's authority
to operate this equipment.