Dooya DM25LEU/S-1.1/28 Instrucciones - Página 2

Navegue en línea o descargue pdf Instrucciones para Persianas Dooya DM25LEU/S-1.1/28. Dooya DM25LEU/S-1.1/28 3 páginas. Tubular motor

Imprimir página

Important Safety Instructions To Be Read Prior To Operation.

Setting Notice

Please read following points of attention carefully before setting.

1. Don't operate motors when low voltage alarm.

2. Operating：

The valid interval of the emitter button is 10S, the emitter will quit the set after 10S.

The motor will run or beep for hint, please do the next step after the hint.

3. Set the limit position：

After the upper / lower limit setting, and the upper / lower limit positin can't at the same position.

After the limit setting, with power off and memory function.

Limit delete will clear all limit memory.

It will exit limit setting when program there is no operation for 2 minutes.

4. If the emitter lost, please set up again with the new emitter.

One motor can store maximum 10 channels; after fully stored, if pair new channels, only the last one will be

covered circularly.

Button Instructions

Micro-USB Port

LED light

Channel

selection"-"

P1 button

(CH-)

Lithium Battery Switch

DD1803H Single-channel Timer Emitter

Dial lithium battery switch, 0 is off switch, 1 is turn on switch.

Functions of P1 button

1. Cycle Operation：

2. Pairing or Pair Additional Emitter：Press P1 button for 2S, motor jog once, release button and make a long noise, motor is

ready for pairing or pair additional emitter.

3. Radio Lock: Press and hold P1 button for 6S, the motor will jog twice, release button and beep twice, the motor enters radio

lock status, the motor won't receive any signal; press P1 button once to disable Radio Lock.

4. Switch Direction: Press and hold P1 button for 10S, the motor will jog 3 times, release button and beep 3 times, the running

direction of the motor has been changed.

5. Reset to Factory Mode: Press and hold P1 button for 14S, the motor will jog 4 times, release button and beep 4 times, the

motor has been reset to factory mode.At this point the motor will go into deep sleep. After entering deep sleep, the motor can't

be controlled. At this time, you need to press P1 button for 2S and then the motor turns to prompt to exit deep sleep.

Essential Settings

The steps in factory mode must be completed to ensure proper operation.

Factory mode

1 Pairing

Press P1 button for 2S (1 jog ), release button and make a long noise,

Or turn the DIP switch to "0" and then to "1"

repower the motor,

within 10S, press STOP for 2S (2 jogs and 3 beeps ),

STOP

the motor has been paired successfully.

* If within 10S, the motor doesn't receive STOP signal from the any emitter, it will exit the paring mode automatically.

Re-power on after power off, if the motor has saved the emitter, there is no rotation prompt, and the code matching

status is not automatically entered at this time.

2 Switch Rotating Direction

(Optional)

If press UP, the motor runs downward, try below to switch direction

Press and hold UP and DOWN buttons simultaneously for 2S, motor

jog once, the direction has been switched successfully.

DOWN

* The operation is only valid when there is no limits. If the motor has already set the upper and lower limit, then you can

only switch direction by P1 button.

-3-

3 Upper and Lower Limits Setting

1 Set upper limit

Press UP for 2S, operate the motor to desired upper

position, press and hold UP and STOP buttons

simultaneously for 2S (2 jogs and 3 beeps), upper limit

is set.

* If exit the limits setting status before you finish the limit setting, then the motor will take the previous limits if has;

After the limits have been set successfully, the motor will enter the user mode.

User mode

1 Add A Preferred Position

1 Set preferred position

STOP

Check both upper and lower limits are set. Operate the

LCD display

product to desired preferred position. Press P2 (1 jog

and 1 beep), press STOP(1 jog and 1 beep), STOP

again (2 jogs and 3 beeps), the preferred position is set.

STOP

* Press STOP for 2S,the motor moves to preferred position automatically.

DOWN

Channel

selection"+"

Jog Mode & Running Mode Switch

(CH+)

Back

DOWN

* When in jog mode, press UP or DOWN once, the motor will be jog running, if press more than 2 second, the motor

will be continously running.

3 Adjust Limits

1 Adjusting the upper limit

STOP

Press and hold UP and STOP buttons for 5S

new upper limit position, press and hold UP and STOP buttons for 2S(2 jogs and 3 beeps), the new upper

limit is programmed successfully.

2 Adjusting the lower limit

DOWN

STOP

Press and hold DOWN and STOP buttons for 5S

(1 jog and make a long

noise),

desired new lower limit position, press and hold DOWN and STOP buttons for 2S (2 jogs and 3 beeps), the

new lower limit is programmed successfully.

* After entering the limits fine tuning mode, the original

operation within 2 minutes, it will arrive within 2 minutes, and the motor will turn to prompt, and automatically exit

the route adjustment mode; When fine-tuning the limit, press and P1 for more than 2S to exit the mode.

4 Pair / Unpair Additional Emitter

Method one

P2(a)

2 Set lower limit

STOP

DOWN

STOP

Press DOWN for 2S, operate the motor to desired

lower position, press and hold DOWN and STOP

buttons simultaneously for 2S (2 jogs and 3 beeps),

lower limit is set.

2 Remove preferred position

STOP

Press P2 (1 jog

and 1

beep), press STOP (1 jog

and 1

beep), STOP again(1 jog

and make a long

noise), the preferred position is deleted.

Press and hold UP and DOWN buttons simultaneously for 5S (1 jog),

press STOP

(1 jog

and make a long noise), switch to jog mode, If

STOP

motor jog twice and beep 3 times, switch to running mode.

The new upper

limit position

DOWN

STOP

(1 jog

and make a long noise), operate the product to desired

The new lower

limit position

DOWN

STOP

(1 jog

and make a long noise), operate the product to

preferred position

will not be deleted; If there is no button

Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing

emitter, press P2 on new emitter to add (2 jogs and 3 beeps), new

emitter is paired to the motor.

•

Repeat same procedure will unpair additional emitter.

P2(b)

-4-

Method two

Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing

emitter, press STOP on new emitter for 2S to add (2 jogs and

3 beeps), new emitter is paired to the motor.

P2(a)

STOP(b)

Method three

Press P1 button for 2S (1 jog), release button and make a long

noise, press STOP on new emitter for 2S to add (2 jogs and

3 beeps), new emitter is paired to the motor.

STOP(b)

•

Repeat same procedure will unpair additional emitter.

* (a) as existing emitter,(b) as new emitter to pair/unpair; Adding the emitter should be carried out when there is a

limits; All the setting of the motor will be kept after addiing the new emitter.

5 Speed Regulation

1 Acceleration setting

Press P2 (1 jog and 1 beep), UP (1 jog and 1 beep), UP again

(2 jogs and 1

beep), the motor running speed is accelerated .

2 Deceleration setting

Press P2 (1 jog and 1 beep), DOWN (1 jog and 1 beep), DOWN

again (2 jogs and

beep), the motor running speed is decelerated.

DOWN

* If the motor no response, it has already been the Max. or Min speed.

Quick Index

Settings

Steps

Pairing

P1 (hold down 2s)

Stop (hold down 2s)

Switch Rotating Direction

Up + Down (hold down 2s)

Set upper limit

Upper and Lower Limits Setting

Set lower limit

Add / Remove Preferred Position

Stop

Jog Mode & Running

Mode Switch

Adjusting the upper limit

Adjust Limits

Adjusting the lower limit

Pair / Unpair Additional Emitter

P1 (hold down 2s)

Stop (b) (hold down 2s)

Acceleration setting

Speed Regulation

Deceleration setting

Down

Troubleshooting

Issues

Possible causes

Battery in motor is depleted

Recharge with compatible AC adaptor

Double check power and cable connections, follow wiring

Power Failure Or Incorrect Connection

instructions.

The motor has no response

emitter battery is low capacity

Replace battery

Check antenna on motor is intact and exposed. Check for

Radio interference / shielding

possible source of radio interference.

Out of radio control range

Try control within closer range

Pair single motor with emitter correctly

The emitter cann't control

Multiple motors are paired to the

same channel.

Try to use multi-channel emitters to control multi-motor

single motor

projects, ensure each channel to control one single motor

Connections are incorrect.

Check connections

The motor doesn't run or starts

too slowly or make loud noise

Installation is improper or overload

Check installation or overload

The motor has reached the lower limit

Adjust the new lower limit

The motor stops during the

up and down running

The running time more than 6min

Consult the sales for more information

-5-

Solution