Flycolor Raptor 390Tower-30A Manual del usuario - Página 2
Navegue en línea o descargue pdf Manual del usuario para Controlador Flycolor Raptor 390Tower-30A. Flycolor Raptor 390Tower-30A 2 páginas. Multi-rotor brushless esc
Imprimir página
Thank you for using our product . Any Improper operation may cause personal injury damage to the
product and related equipments. This high power system for RC model can be dangerous ,we strongly
recommend reading the user manual carefully and completely. We will not assume any responsibility for any
losses caused by unauthorized modifications to our product. We have the right to change the design,
ATTENTION
appearance, performance and usage requirements of the product without notice.
01
Main features
● Using C8051F390 MCU
,pipelined 8-bit C8051 core with 50 MHz maximum operating frequency;
●
Using dedicated 3in1 drivers, faster response, small size&lighter in weight.
● Two layers tower structure between the 4in1 ESC and FC with quick pin connection. The interference caused by the signal
transmission is reduced to the maximum extent, and the flight is more stable, make the whole weight lighter, and the
installation is faster and more convenient;
● Standard F3 flight controller, Supports PPM, PWM and SBUS remote control / receiving mode;
● FC integrated OSD, also integrated 5V, 12V, and battery voltage (VBAT), Easy power supply to Image transmitter, camera,
buzzer, LED and other peripheral ; Provided all kind of cables for connectors on FC , to give you an unprecedented
experience of installation;
● Use BLHeli open-source firmware; Using "Damped light" mode , it improves the throttle response, when reducing the throttle
amount, the Motors slow down rapidly. It strengthens the stability and flexibility of multi-rotors, quite suitable for QAVs.
●
Supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot
(5-25us). The input signal is automatically detected by the ESC upon power up.
02
Specifications
Burst Current
Model
Con. Current
(10S)
Raptor 390Tower-20A
20A
30A
Raptor 390Tower-30A
30A
40A
*Raptor 390Tower ESC is using the Flycolor Raptor390 20A Multi BLHeli firmware ;F.C is using SPRACINGF3 firmware;
Please contact Flycolor for more information.
03
Part list / Install Dimensions
Description
Qty.
Item
1
Raptor 390 4in1 ESC
1
Flight Controller
2
1
Nylon spacer M3*5+6
3
4
Nylon Nut M3
4
8
5
Nylon screw M3*12
4
For quick plug, Flight Controller additionally provide:：
one 10p cable (10-pin SH1.0 terminal) for PWM or PPM connectors;
one 3p cable (4-pin SH1.0 terminal)for SBUS connector;
one 6p cable (6-pin SH1.0 terminal)for LED and Buzzer.
three 4p cables(4-pin SH1.0 ) for different brand Image Transmitters.
two 3p cables (3-pin SH1.0 )for different brand Cameras;
Attention: For these quick plug cables, please confirm the wire
sequences on your devices' connector are corresponding with the
Flight controller before connecting. If the terminals are not fit your
devices ,please make a modified connection to fit.
04
Connect diagram of ESC and FC
ESC
3
+
Battery V
-
B
attery
V
1
Multi-Rotor Brushless ESC
Raptor 390 Tower
ESC maximum speed is limited to 400k eRPM;
Size
Weight
BEC
LiPo cells
(For reference)
19.5g
No
2-4S
41.5x36x15.1mm
19.5g
No
2-4S
41.5x36x15.1mm
Dimensions(mm)
4
2
3
1
机架
（供参考）
5
*All pictures are for reference only
4
otor
4#M
●
All welding requires good welding technology,
4#M
otor
short circuit between the element
4#M
otor
or the wire should be avoided at any time.
●
Please ensure all solder joints are insulated
otor
2#M
with heat shrink where necessary.
ATTENTION
otor
●Please double-check the polarity is correct
2#M
before power up.
otor
2#M
2
User Manual
Bridged
for recovering firmware
RAPTOR
390 Tower
Current meter
A D 1
9
BLHeli
10
RSSI
AD2
ISP programming
(OSD Debug)
Bridged
for recovering firmware
GND
PPM
1
5V
2
receiver
CH1
3
Typical Applications
(For reference)
Current meter
A D 1
9
10
RSSI
AD2
Multi
130-330
ISP programming
170-450 Multi
(OSD Debug)
Bridged
for recovering firmware
GND
1
5V
2
PWM
CH1
3
CH2
4
receiver
CH3
5
41.5
CH4
6
CH5
7
CH6
8
30.5
Current meter
A D 1
9
10
RSSI
AD2
ISP programming
(OSD Debug)
05
36
Attention
● User need to calibrate the throttle range when starting to use a new ESC or another transmitter.
● BLHeli open-source firmware, when some abnormality occurs in ESC driving the motor or need the motor to reach a higher RPM, user can try to
change the timing.
● User also can connect the flight control to the computer to update the firmware or change the setup via
● Observe polarity at all times. Check and double check before applying power.
● Power off before unplugging ,plugging in or making any connections.
● 5V ,12Vsupply is for low-current use only(5V 1A MAX, 12V 500mA MAX,12V is suggested for camera only).
● Keep magnets away from the Flight Controller.
● Do everything you can to prevent vibrations.
● Please contact Flycolor sales or technical support for more information.
User Manual
Multi-Rotor Brushless ESC
TOP
SBUS Mode
"BOOT"
Smart Port Pad
RX
4
SBUS
GND
RX
5V
TX
2
5V
receiver
CH1
5V
CH2
GND
GND
1
CH3
CH4
CH5
CH6
AD1
AD2
S
12V
S
NC
12V
12V
5V
camera
GND
Reset
GND
RX
TX
GND
Image
transmitter
TOP
PPM Mode
"BOOT"
Smart Port Pad
4
RX
3
TX
GND
RX
5V
TX
UART3
2
5V
CH1
5V
CH2
GND
GND
1
CH3
CH4
CH5
CH6
AD1
AD2
S
12V
S
NC
12V
12V
5V
GND
camera
Reset
GND
RX
TX
GND
Image
VBAT
transmitter
PWM Mode
TOP
"BOOT"
Smart Port Pad
RX
4
3
TX
GND
RX
5V
TX
UART3
2
5V
CH1
5V
CH2
GND
GND
1
CH3
CH4
CH5
CH6
AD1
AD2
S
12V
S
NC
12V
12V
5V
camera
GND
Reset
GND
RX
TX
GND
Image
transmitter
BOTTOM
Buzzer
6
5V
Buzzer
5
Buzzer
5V
GND
3
LED
LED
5V
2
5V
LED
GND
GND
1
GND
VBAT
GND
-
S
VBAT
VBAT
+
GND
S
BOTTOM
Buzzer
6
5V
Buzzer
5
Buzzer
5V
GND
3
LED
LED
5V
2
5V
LED
GND
1
GND
GND
VBAT
GND
-
S
VBAT
+
GND
S
BOTTOM
Buzzer
6
Buzzer
5V
5
Buzzer
5V
GND
3
LED
LED
5V
2
5V
LED
GND
GND
1
GND
VBAT
GND
-
S
VBAT
VBAT
+
GND
S
configuration software (BLHeliSuite)
.
www.flycolor.net
251400-1058-02