Flying Industry Development 0020703 Manual rápido - Página 2

Navegue en línea o descargue pdf Manual rápido para Mando a distancia Flying Industry Development 0020703. Flying Industry Development 0020703 4 páginas. Rf wireless remote control radio controller / transmitter & receiver

Imprimir página
following circuit diagram, then you use the transmitter to control the AC 380V motor.
Setting different control modes:
We have set the receiver as Latched control mode before delivery. If you want to use other control modes, do as following operation:
1) Setting control mode Momentary: When the receiver is in the status of LEARNING, press button ▼ of first row of the transmitter.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button ▲ of first row of the transmitter, the contactor 1 is connected, the 380V motor 1 rotates in the positive direction.
Release button ▲ of first row, the contactor 1 is disconnected, the 380V motor 1 stops.
Press and hold button ▼ of first row of the transmitter, the contactor 2 is connected, the 380V motor 1 rotates in the reversal direction
Release button ▼ of first row, the contactor 2 is disconnected, the 380V motor 1 stops.
Press and hold button ▲ of second row of the transmitter, the contactor 3 is connected, the 380V motor 2 rotates in the positive direction.
Release button ▲ of second row, the contactor 3 is disconnected, the 380V motor 2 stops.
Press and hold button ▼ of second row of the transmitter, the contactor 4 is connected, the 380V motor 2 rotates in the reversal direction
Release button ▼ of second row, the contactor 4 is disconnected, the 380V motor 2 stops.
2) Setting control mode Latched: When the receiver is in the status of LEARNING, press button ▼ of second row of the transmitter.
Press button ▲ of first row of the transmitter, only the contactor 1 is connected, the 380V motor 1 rotates in the positive direction.
Press button ▼ of first row of the transmitter, only the contactor 2 is connected, the 380V motor 1 rotates in the reversal direction;
Press button ▲ of second row of the transmitter, only the contactor 3 is connected, the 380V motor 2 rotates in the positive direction;
Press button ▼ of second row of the transmitter, only the contactor 4 is connected, the 380V motor 2 rotates in the reversal direction;
Wired control terminals:
The receiver has manual control terminals, you can connect external devices, sensors (normally open type), or manual switches to control the
receiver.
You can connect manual switches to terminals "GND", "KA", "KB", "KC", "KD", "KE", then you can use manual switches to control equipment.
1) Control mode Momentary:
When connect terminals "GND" and "KA", the contactor 1 is connected, the 380V motor 1 rotates in the positive direction.
And when disconnect "GND" and "KA", the contactor 1 is disconnected, the 380V motor 1 stops.
When connect terminals "GND" and "KB", the contactor 2 is connected, the 380V motor 1 rotates in the reversal direction.
And when disconnect "GND" and "KB", the contactor 2 is disconnected, the 380V motor 1 stops.
When connect terminals "GND" and "KC", the contactor 3 is connected, the 380V motor 2 rotates in the positive direction.
And when disconnect "GND" and "KC", the contactor 3 is disconnected, the 380V motor 2 stops.
When connect terminals "GND" and "KD", the contactor 4 is connected, the 380V motor 2 rotates in the reversal direction.
And when disconnect "GND" and "KD", the contactor 4 is disconnected, the 380V motor 2 stops.
2) Control mode Latched:
When connect terminals "GND" and "KA", only the contactor 1 is connected, the 380V motor 1 rotates in the positive direction.
When connect terminals "GND" and "KB", only the contactor 2 is connected, the 380V motor 1 rotates in the reversal direction.
When connect terminals "GND" and "KE", four contactors are disconnected, the 380V motor 1 stops.
When connect terminals "GND" and "KC", only the contactor 3 is connected, the 380V motor 2 rotates in the positive direction.
When connect terminals "GND" and "KD", only the contactor 4 is connected, the 380V motor 2 rotates in the reversal direction.
When connect terminals "GND" and "KE", four contactors are disconnected, the 380V motor 2 stops.
Learning the button of remote control:
1) Press the learning button of the receiver for 1- 2 seconds, release the button, lights on. The receiver enters into status of LEARNING.
2) Within 5 seconds, press any button on transmitter. If lights flash five times and lights off, it means learning is successful.
3) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Pressing learning buttons on the receiver until the signal light flashes, release the button. That means all stored codes have been deleted
successfully.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com