Flying Industry Development S1PX-DC12-ANT2 Manual rápido

Navegue en línea o descargue pdf Manual rápido para Mando a distancia Flying Industry Development S1PX-DC12-ANT2. Flying Industry Development S1PX-DC12-ANT2 3 páginas. Rf wireless receiver

Imprimir página
RF Wireless Receiver (Model 0020438 S1PX-DC-ANT2)
Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship,
offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks,
motors, fans, pumps, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
Wireless remote control, easy to install.
Super long working range, with a transmitter to form a complete set, the working distance can reach 2000m in an open ground.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Power Supply: Four working voltage versions, DC 6V, 9V, 12V, 24V.
DC Power Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.
High Power: Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V, 270W/9V or 720W/24V.
With
wired control
terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
With external magnetic sucker antenna and a 1.5 meters cable, the antenna can be installed outside the building to get better working distance.
You can control the equipments by using the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With characteristics of reverse power protection and over current protection.
Reliable control: The code has thousands of different combinations, and the receiver only works with the transmitter which use the same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No.: S1PX-DC06 -ANT2/ S1PX-DC09 -ANT2 / S1PX-DC12 -ANT2 / S1PX-DC24 -ANT2
Power Supply (Operating Voltage): DC6V (S1PX-DC06-ANT2), DC9V±1V (S1PX-DC09-ANT2), DC12V±1V (S1PX-DC12-ANT2), DC24V±2V
(S1PX-DC24 -ANT2)
Output: DC6V (S1PX-DC06 -ANT2), DC9V (S1PX-DC09 -ANT2), DC12V (S1PX-DC12 -ANT2), DC24V (S1PX-DC24 -ANT2)
Wire range for the terminals: 22-9 AWG
Working Frequency: 315MHz / 433MHz
Channel: 1 CH
Control Modes: Toggle, Momentary, Latched
Static Current: ≤6mA
Operating Temperature: -20 ° C to +70 ° C
Maximum Working Current: 30A
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
External Magnetic Sucker Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 1.5m, we also can offer longer cable, such as 5 meters, 10 meters or 30 meters.
Anti-interference, waterproof, shielded wire set inside.
Magnetic stand design for easy to install.
Matching Transmitters For Receiver:
The receiver can work with different transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2 (500M), or CB-1
/ CB-2 (1000M) etc.
When you set the receiver in toggle or momentary mode, it should work with single button transmitter, such as model C-1 (100M), CWB-1 (50M,
waterproof), CP-1 (500M), or CB-1 (1000M) etc. When you set the receiver in latched mode, it should work with two buttons transmitter, such as
model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2 (500M), or CB-2 (1000M) etc.
Working Range:
Super long range, with a transmitter (such as CB-2) to form a complete set, the maximum working distance can reach 2000M in an open ground.
The maximum working distance is an ideal range , it shall be operated with no barriers and interference in an open ground. But in the practice, it will
be hindered by trees, walls or other constructions, and will be interfered by other wireless sign. Therefore, the actual distance may not reach this
maximum working distance.
Usage (with the transmitter CB-2):
The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose the
receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V
version.
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal "L / +" of INPUT, and connect the negative pole of DC power supply to terminal "N / -" of
INPUT.
2) Connect the positive pole of lamp to terminal "L / +" of OUTPUT, and connect the negative pole of lamp to terminal "N / -" of OUTPUT.
Setting different control modes:
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com