Canon EF-M Instrucciones

Navegue en línea o descargue pdf Instrucciones para Objetivo de la cámara Canon EF-M. Canon EF-M 2 páginas. Ef-m11-22mm f/4-5.6 is stm
También para Canon EF-M: Manual de instrucciones (40 páginas), Manual de instrucciones (22 páginas)

Imprimir página

CT1-8587-001

EF-M LENS Instructions

ENG

EF-M11-22mm f/4-5.6 IS STM

⑩

⑧

①

⑦

②

⑥

③

④

Nomenclature

① Focusing ring

② Hood mount

③ Filter Mounting Thread

④ Lens mount index

⑤ Contacts

⑥ Zoom position index

⑦ Lens retracted position index

⑧ Zoom ring

⑨ Focal length indicator

⑩ Lens-retraction switch

Thank you for purchasing a Canon product.

The Canon EF-M11-22mm f/4-5.6 IS STM is a 2x wide-

angle zoom lens developed for interchangeable-lens digital

cameras compatible with EF-M lenses*.

* Only the following cameras are compatible with EF-M lenses (as

of June 2013):

EOS M

When attaching this lens to a Canon EOS M camera with

firmware earlier than version 2.0.0, there is a slight chance

that the camera will not operate properly during shooting.

Therefore, please be sure to update the EOS M firmware to

version 2.0.0 or later (For information about updating your

camera's firmware, please check the Canon website).

• "IS" stands for Image Stabilizer.

• "STM" stands for stepping motor.

Safety Precautions

• Do not look at the sun or a bright light source through

the lens. Doing so could result in vision loss or blindness.

• Whether it is attached to the camera or not, do not

⑨

leave the lens under the sun without the lens cap

attached. This is to prevent the lens from concentrating the

sun's rays, which could cause a fire.

Handling Cautions

• If the lens is taken from a cold environment into a warm

one, condensation may develop on the lens surface

and internal parts. To prevent condensation in this case,

first put the lens into an airtight plastic bag before taking it

from a cold to warm environment. Then take out the lens

after it has warmed gradually. Do the same when taking the

lens from a warm environment into a cold one.

• Do not leave the lens in excessive heat such as in a car in direct

sunlight. High temperatures can cause the lens to malfunction.

• Please also refer to the handling cautions found in your

camera's instructions.

Conventions used in this instruction

⑤

Warning to prevent lens or camera malfunction or

damage.

Supplementary notes on using the lens and taking

pictures.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Do not make any changes or modifications to the equipment

unless otherwise specified in the instructions. If such changes

or modifications should be made, you could be required to stop

operation of the equipment.

This equipment has been tested and found to comply with

the limits for a class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-

003.

1. Mounting and Detaching the Lens

See your camera's instructions for details on mounting and

detaching the lens.

•

After detaching the lens, place the lens with the rear end

up to prevent the lens surface and contacts from getting

scratched. (fig.❶)

•

If the contacts get soiled, scratched, or have fingerprints

on them, corrosion or faulty connections can result. The

camera and lens may not operate properly.

•

If the contacts get soiled or have fingerprints on them, clean

them with a soft cloth.

•

If you remove the lens, cover it with the dust cap. To

attach it properly, align the lens mount index and the 

index of the dust cap as shown in the diagram, and turn

clockwise. (fig.❷) To remove it, reverse the order.

2. Shooting Preparations and Retracting Lens

Shooting Preparations: (Set the lens to the shooting

position)

Align the lens retract position index and zoom position index.

Maintain pressure on the lens-retraction switch in the [▲]

direction. Slightly rotate the zoom ring in the direction of the

white arrow to release the lens-retraction switch and rotate

further until it clicks. The lens now ready for shooting. (The no.

11 pointing line in the focal length indicator which shows above

or to the left of the zoom position index extension line.) (fig.❸)

Retracting Lens:

Maintain pressure on the lens-retraction switch in the [▲]

direction. Rotate the zoom ring in the opposite direction to the

white arrow. Align the lens retract position index and the zoom

position index. Release the lens-retraction switch to retract the

lens.

Do not forcibly rotate the zoom ring if its movement

becomes constricted at the retractable end or the wide

end, as there is a danger of damaging the lens-retraction

switch mechanism.

3. Zooming

Turn the lens' zoom ring to adjust the size of the photo field or

subject. (fig.❹)

• For wide shots, turn the zoom ring toward the wide end.

• For close-ups, turn the zoom ring toward the telephoto end.

•

Be sure to finish zooming before focusing. Zooming after

focusing can affect the focus.

•

Blurring may temporarily occur if the zoom ring is quickly

rotated.

•

Zooming during still image exposure will result in delayed

focus. This causes any streaks of light that are captured

during exposure to be blurred.

❶

❷

❸

❹

Wide end

Telephoto end

Zoom ring

ENG-1