Cole Parmer Electrothermal MC242 Manual de instrucciones - Página 6
Navegue en línea o descargue pdf Manual de instrucciones para Controlador Cole Parmer Electrothermal MC242. Cole Parmer Electrothermal MC242 20 páginas. Heating controller
Imprimir página
3.1. Prevention of Fire and Electric shock.
3.2. General Safe Operating Practice.
Do not obstruct the ventilation slots in the controller base.
It is not recommended to leave any heating apparatus unattended
during operation.
Only use original equipment manufacturer's spares and accessories. Refer to
3.2. General Safe Operating Practice.
section 10.
The equipment is not spark, flame or explosion proof and has not been
3.2. General Safe Operating Practice.
designed for use in hazardous areas in terms of BSEN 60079-14:1997.
Keep flammable, low flash point substances away from heating apparatus.
3.2. General Safe Operating Practice.
Do not operate or handle any part of this product with wet hands.
3.2. General Safe Operating Practice.
Do not leave this product switched on without glass sides in place for
prolonged periods.
Keep the mains plug and lead set cable away from the heating apparatus
being controlled.
Refer to instruction manual for the resistive load of equipment to ensure
controller is suitable for application.
NOTE: if this product is not used in accordance with the Manufacturer's Instructions then the basic
Page 5 of 24
safety protection afforded by the equipment may not be preserved and the guarantee invalidated.
Always observe the manufacturer's operating and safety instructions for the
Page 5 of 24
equipment to be connected to the controller.
Page 5 of 24
NOTE: if this product is not used in accordance with the manufacturer's instructions
then the basic safety protection afforded by the equipment may not be preserved and
the guarantee invalidated.
Page 5 of 24
Page 5 of 24
Page 5 of 24
Page 5 of 24
Page 5 of 24
applicable to your areas of operation. Check laboratory procedures
Replace fuses only with the type as listed in section, Parts and
Ensure the Mains Power Supply conforms to rating found on the
Always follow good laboratory practice when using this
whilst power is applied.
arise have been suitably addressed before proceeding. When
product case without authorisation. Only qualified Service
Accessories and Technical Specifications. (See fuse type and
for substances being heated and ensure all hazards (e.g. explosion,
data plate located on the base of this product.
equipment. Give due recognition to your company's safety and
heating certain substances the liberation of hazardous gases may
personnel should attempt to repair this Controller.
implosion or the release of toxic or flammable gases) that might
rating).
legislative health & safety procedures and all associated legislation
Never Operate this equipment with out connection to earth /
require the use of a fume cupboard or other means of extraction.
arise have been suitably addressed before proceeding. When
To prevent a risk of fire or electric shock, DO NOT open your
applicable to your areas of operation. Check laboratory procedures
Replace fuses only with the type as listed in section, Parts and
Ensure the Mains Power Supply conforms to rating found on the
Always follow good laboratory practice when using this
ground. Ensure the mains supply voltage is correctly earthed /
heating certain substances the liberation of hazardous gases may
product case without authorisation. Only qualified Service
for substances being heated and ensure all hazards (e.g. explosion,
Ensure equipment is used on a clean, dry, non-combustible, solid
Accessories and Technical Specifications. (See fuse type and
data plate located on the base of this product.
equipment. Give due recognition to your company's safety and
grounded in accordance with current area legislation.
require the use of a fume cupboard or other means of extraction.
personnel should attempt to repair this Controller.
implosion or the release of toxic or flammable gases) that might
work surface with at least 300mm suitable clearance all around
rating).
legislative health & safety procedures and all associated legislation
Never Operate this equipment with out connection to earth /
arise have been suitably addressed before proceeding. When
Do not install or remove any heating apparatus from the controller
from other equipment.
Ensure equipment is used on a clean, dry, non-combustible, solid
applicable to your areas of operation. Check laboratory procedures
Replace fuses only with the type as listed in section, Parts and
Ensure the Mains Power Supply conforms to rating found on the
ground. Ensure the mains supply voltage is correctly earthed /
heating certain substances the liberation of hazardous gases may
whilst power is applied.
work surface with at least 300mm suitable clearance all around
Accessories and Technical Specifications. (See fuse type and
for substances being heated and ensure all hazards (e.g. explosion,
Do not position the product so that it is difficult to disconnect from
data plate located on the base of this product.
grounded in accordance with current area legislation.
require the use of a fume cupboard or other means of extraction.
from other equipment.
rating).
implosion or the release of toxic or flammable gases) that might
the mains supply.
Never Operate this equipment with out connection to earth /
Do not install or remove any heating apparatus from the controller
arise have been suitably addressed before proceeding. When
Ensure equipment is used on a clean, dry, non-combustible, solid
Do not position the product so that it is difficult to disconnect from
Ensure the Mains Power Supply conforms to rating found on the
Do not immerse unit in water or fluids.
ground. Ensure the mains supply voltage is correctly earthed /
Always follow good laboratory practice when using this
whilst power is applied.
heating certain substances the liberation of hazardous gases may
work surface with at least 300mm suitable clearance all around
the mains supply.
data plate located on the base of this product.
grounded in accordance with current area legislation.
equipment. Give due recognition to your company's safety and
require the use of a fume cupboard or other means of extraction.
from other equipment.
legislative health & safety procedures and all associated legislation
Do not immerse unit in water or fluids.
The equipment is not spark, flame or explosion proof and has not
Never Operate this equipment with out connection to earth /
Do not spill substances onto this unit. If spillage does occur,
Do not install or remove any heating apparatus from the controller
Ensure equipment is used on a clean, dry, non-combustible, solid
Do not position the product so that it is difficult to disconnect from
applicable to your areas of operation. Check laboratory procedures
been designed for use in hazardous areas in terms of BSEN 60079-
ground. Ensure the mains supply voltage is correctly earthed /
disconnect unit from mains supply and follow instructions as
Always follow good laboratory practice when using this
whilst power is applied.
work surface with at least 300mm suitable clearance all around
the mains supply.
for substances being heated and ensure all hazards (e.g. explosion,
14:1997. Keep flammable, low flash point substances away from
grounded in accordance with current area legislation.
detailed in Section 'Maintenance'.
equipment. Give due recognition to your company's safety and
Do not spill substances onto this unit. If spillage does occur,
from other equipment.
implosion or the release of toxic or flammable gases) that might
heating apparatus.
Do not immerse unit in water or fluids.
legislative health & safety procedures and all associated legislation
disconnect unit from mains supply and follow instructions as
Do not install or remove any heating apparatus from the controller
To prevent electronic overheat and potential fire
arise have been suitably addressed before proceeding. When
Do not position the product so that it is difficult to disconnect from
applicable to your areas of operation. Check laboratory procedures
detailed in Section 'Maintenance'.
Do not operate or handle any part of this product with wet hands.
Always follow good laboratory practice when using this
whilst power is applied.
Do not cover this product when connected to the mains power
heating certain substances the liberation of hazardous gases may
the mains supply.
for substances being heated and ensure all hazards (e.g. explosion,
Do not spill substances onto this unit. If spillage does occur,
equipment. Give due recognition to your company's safety and
supply.
require the use of a fume cupboard or other means of extraction.
To prevent electronic overheat and potential fire
implosion or the release of toxic or flammable gases) that might
disconnect unit from mains supply and follow instructions as
legislative health & safety procedures and all associated legislation
Do not immerse unit in water or fluids.
Do not cover this product when connected to the mains power
Keep the Mains Plug and Lead set cable away from the
It is not recommended to leave any heating apparatus unattended
arise have been suitably addressed before proceeding. When
Ensure equipment is used on a clean, dry, non-combustible, solid
detailed in Section 'Maintenance'.
applicable to your areas of operation. Check laboratory procedures
Always follow good laboratory practice when using this
supply.
heating apparatus being controlled.
during operation.
heating certain substances the liberation of hazardous gases may
work surface with at least 300mm suitable clearance all around
for substances being heated and ensure all hazards (e.g. explosion,
equipment. Give due recognition to your company's safety and
Do not spill substances onto this unit. If spillage does occur,
To prevent electronic overheat and potential fire
require the use of a fume cupboard or other means of extraction.
It is not recommended to leave any heating apparatus unattended
from other equipment.
Refer to Instructions book / product data label for the resistive load
implosion or the release of toxic or flammable gases) that might
Only use Original Equipment manufacture's spares and
legislative health & safety procedures and all associated legislation
disconnect unit from mains supply and follow instructions as
Do not cover this product when connected to the mains power
during operation.
of equipment to ensure controller is suitable for application.
arise have been suitably addressed before proceeding. When
accessories. Ref Section 11.
Ensure equipment is used on a clean, dry, non-combustible, solid
applicable to your areas of operation. Check laboratory procedures
Do not position the product so that it is difficult to disconnect from
detailed in Section 'Maintenance'.
supply.
heating certain substances the liberation of hazardous gases may
work surface with at least 300mm suitable clearance all around
for substances being heated and ensure all hazards (e.g. explosion,
the mains supply.
Only use Original Equipment manufacture's spares and
Always observe the Manufacturer's operating and safety
To prevent electronic overheat and potential fire
It is not recommended to leave any heating apparatus unattended
require the use of a fume cupboard or other means of extraction.
from other equipment.
implosion or the release of toxic or flammable gases) that might
accessories. Ref Section 11.
instructions for the equipment to be connected to the controller.
Do not immerse unit in water or fluids.
Do not cover this product when connected to the mains power
during operation.
arise have been suitably addressed before proceeding. When
Ensure equipment is used on a clean, dry, non-combustible, solid
Do not position the product so that it is difficult to disconnect from
supply.
heating certain substances the liberation of hazardous gases may
Only use Original Equipment manufacture's spares and
work surface with at least 300mm suitable clearance all around
the mains supply.
Do not spill substances onto this unit. If spillage does occur,
require the use of a fume cupboard or other means of extraction.
It is not recommended to leave any heating apparatus unattended
accessories. Ref Section 11.
from other equipment.
disconnect unit from mains supply and follow instructions as
Do not immerse unit in water or fluids.
during operation.
Ensure equipment is used on a clean, dry, non-combustible, solid
Do not position the product so that it is difficult to disconnect from
detailed in Section 'Maintenance'.
work surface with at least 300mm suitable clearance all around
Only use Original Equipment manufacture's spares and
the mains supply.
Do not spill substances onto this unit. If spillage does occur,
To prevent electronic overheat and potential fire
from other equipment.
accessories. Ref Section 11.
Do not immerse unit in water or fluids.
disconnect unit from mains supply and follow instructions as
Do not cover this product when connected to the mains power
Do not position the product so that it is difficult to disconnect from
detailed in Section 'Maintenance'.
supply.
the mains supply.
Do not spill substances onto this unit. If spillage does occur,
To prevent electronic overheat and potential fire
It is not recommended to leave any heating apparatus unattended
Do not immerse unit in water or fluids.
disconnect unit from mains supply and follow instructions as
Do not cover this product when connected to the mains power
during operation.
detailed in Section 'Maintenance'.
supply.
Only use Original Equipment manufacture's spares and
Do not spill substances onto this unit. If spillage does occur,
To prevent electronic overheat and potential fire
It is not recommended to leave any heating apparatus unattended
accessories. Ref Section 11.
disconnect unit from mains supply and follow instructions as
Do not cover this product when connected to the mains power
during operation.
detailed in Section 'Maintenance'.
supply.
Only use Original Equipment manufacture's spares and
To prevent electronic overheat and potential fire
It is not recommended to leave any heating apparatus unattended
accessories. Ref Section 11.
Do not cover this product when connected to the mains power
during operation.
supply.
Only use Original Equipment manufacture's spares and
It is not recommended to leave any heating apparatus unattended
accessories. Ref Section 11.
during operation.
Only use Original Equipment manufacture's spares and
accessories. Ref Section 11.
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
M6493 Issue 10.3
6