Canyon Cottage Colors 3682801P Manual de instrucciones de montaje - Página 6

Navegue en línea o descargue pdf Manual de instrucciones de montaje para Mobiliario interior Canyon Cottage Colors 3682801P. Canyon Cottage Colors 3682801P 16 páginas. Bunk bed

Imprimir página
TWIN OVER TWIN LOFT BUNK WITH LOFT DRESSER ASSEMBLY INSTRUCTIONS
LIST OF CONTENTS
28-705 TOP BUNK END FIG.1
A.- (1) TOP BUNK BED END
HARDWARE PACK (HPK00123-0)
B.- (2) 4"METAL DOWEL PINS
28-207 LOFT DRESSER FIG.2
C.- (1) LOFT DRESSER
28-766 LOFT HUTCH FIG.3
E.- (1) LOFT HUTCH
HARDWARE PACK (HPK00012-0)
B.- (2) 4"METAL DOWEL PINS
28-730 4 SIDE RLS/2 GUARD RLS FIG.4
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
HARDWARE PACK (HPK00104-0)
H.- (24) 80MM FLAT HEAD BOLTS
I.- (24) 5/16"-18 X 5/8" CROSS DOWEL NUTS
J.- (1) 5MM ALLEN WRENCH
28-707 TWIN BOTTOM HDBD & FTBD FIG.5
T.- (1) HEADBOARD
U.- (1) FOOTBOARD
HARDWARE PACK (HPK00127-0)
V.- (4) CASTERS
28-720 LADDER FIG.6
N.- (1) LADDER
HARDWARE PACK (HPK00008-0)
O.- (2) METAL HOOK BRACKETS
P.- (6) 1" SCREWS
28-706 TWIN BUNKBED ENDS FIG.7
S.- (1) 1 PC BUNK BED END TWIN
TOP BUNK BED
1.- ASSEMBLE
2.- TAKE LOFT DRESSER (C), AND PLACED IT IN THE ROOM'S DESIRED POSITION, PLACE IT FACING OUTWARDS.
3.- INSERT TWO DOWEL PINS (B ) ON TOP IN EACH OUTSIDE CORNER OF LOFT DRESSER (C ), TAKE THE LOFT HUTCH (E ), AND PLACE IT ON TOP OF LOFT DRESSER ALIGNING
METAL DOWEL PINS WITH EACH PRE-DRILLED HOLE IN BOTH ENDS UNTIL THE METAL DOWEL PINS ARE ALL IN,
4.- INSERT TWO CROSS DOWEL NUTS (I) IN ACCESS HOLE INSIDE SIDE RAIL & GUARD RAIL, ALIGN CROSS DOWEL NUT MAKE SURE THE GROOVE IS HORIZONTAL, (FIG.A)
5.- ATTACH TWO SIDE RAILS AND TWO GUARDRAILS TO DRESSER/HUTCH/TOP BUNK BED ASSEMBLY AND 1 PC BUNK BED END TWIN (S ), INSERTING TWO FLAT BOLTS (H ) INTO
TOP BUNK BED AND 1 PC BUNK BED END TWIN HOLES, USE ALLEN WRENCH TO TIGHTEN BOLTS,
CONNECTED TOGETHER )
6.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH ENDS, PUSH THE SLAT AGAINST THE BED END POST (FIG.B) AND TWO SLATS IN THE MIDDLE AT
EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH TWO 1 1/4" SCREWS (S), SEE FIG.11
FIG.9
FRONT
REV 03 05/08/2019
CANYON FURNITURE COMPANY
FIG.3
N
S
100-645 TWIN SLATS FIG.8 (2PCS)
, USING ONE TOP BUNK BED END (A), ONE LOFT DRESSER (C), ONE LOFT HUTCH (E), TWO SIDE RAILS (F), AND TWO GUARD RAILS (G).
FIG.10
,
FIG.10
HARDWARE PACK
A
HPK00123-0
B
FIG.1
HARDWARE PACK
E
HPK00012-0
B
HARDWARE PACK
HPK00008-0
P
O
FIG.6
FIG.9
HARDWARE PACK
HPK00016-0
Q
R
FIG.8
Q.- (4) SLATS
HARDWARE PACK (HPK00016-0)
R.- (8) 1 1/4" SCREWS
( DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE
FIG.11
FIG.11
PAGE 2 OF 4
FIG.2
F
G
FIG.4
T
TOOLS NEEDED
PHILIPS HEAD SCREWDRIVER (NOT INCLUDED)
5MM ALLEN WRENCH (INCLUDED)
SEE FIG.9
YES,
HORIZONTAL
GROOVE
NO
FIG.B
KIS01179-2B
C
HARDWARE PACK
HPK00104-0
H
J
I
U
FIG.5
HARDWARE PACK
HPK00127-0
V
FIG.A