Baumer ISI31.010AX01 Manual de instrucciones - Página 7

Navegue en línea o descargue pdf Manual de instrucciones para Caja Baumer ISI31.010AX01. Baumer ISI31.010AX01 20 páginas. Display counter

Imprimir página

Operating instructions

LCD Display counters

isiLine 30/31/32/33

Description

The isiLine display counters are battery-powered. They are con-

trolled by contact or voltage pulses. They may be used in various

applications, like e. g. totalising, parts counting, position

acquisition, differential counting, etc. In addition, the various

models with specific input types may be extended using control

inputs to select operatin modes and set for almost any applica-

tion thanks to adjustable operating modes.

1.1 Preface

Please read this instruction manual carefully before

installation and start-up. Please observe all warn-

ings and advices, both for your own safety and for

general plant safety. If the device is not used in

accordance with this instruction manual, then the

intended protection can be impaired.

1.2 Safety Instructions and Warnings

Please use the device only if its technical condition

is perfect. It should be used only for its intended

purpose. Please bear in mind safety aspects and

potential dangers and adhere to the operating

instructions at all times. The safety standards in

force for electrical installations are also to be

adhered to.

1.3 Use according to the intended purpose

The application area for this device lies in industrial processes

and controls, in the fields of manufacturing lines for the metal,

wood, plastics, paper, glass, textile and other like industries with

a degree of contamination of 2. Over voltages at the terminals

of the device must be kept within the limits of Over voltage

Category II. The device is not suitable for use in hazardous areas

and for areas excluded from EN 61010 Part 1. The device may

only be operated indoors as a panel-mounted device. However,

in certain conditions, an outdoor operation is also allowed. It

may be operated up to an altitude of 2,000 m. Use for any pur-

pose over and beyond this will be deemed as not in accordance

with its intended purpose.

If the device is used to monitor machines or processes in which,

in the event of a failure of the device or an error made by the

operator, there might be the risk of damaging the machine or

causing an accident to the operators, then it is your responsibili-

ty to take the appropriate safety measures.

1.4 Mounting in a control panel

Mount the device away from heat sources and avoid

direct contact with corrosive liquids, hot steam or

similar. When mounting the device, make sure it is

sufficiently cooled.

1.5 Mounting instructions

– Remove the mounting clip from the device.

– Insert the device from the front into the panel cut-out, ensur-

ing the front-panel gasket is correctly seated.

– Slide the fixing clip from the rear onto the housing, until the

spring clamps are under tension and the upper and lower

latching lugs have snapped into place.

1.6 Electrical installation

This device is powered by an internal battery

– In order to respect the fire protection regulations,

8 A/150 VA shall not be exceeded on the counter

in case of a defect!

– Do not wire the terminals of the device that are

not used.

– The pin assignment of the connectors, as well as

the maximum admissible values, must obligatorily

be observed.

– An EMC-compliant installation is a prerequisite to

reach EC conformity.

1.7 Advice on noise immunity

All connections are protected against external sources of inter-

ference. The installation location should be chosen so that induc-

tive or capacitive interference does not affect the device or its

connecting lines! Interference (e.g. from switch-mode power

supplies, motors, clocked controllers or contactors) can be

reduced by means of appropriate cable routing and wiring.

1.8 Measures to be taken:

– Use only shielded cable for signal and control lines.

– Connect cable shield at both ends.

– The conductor cross-section of the cables should be a mini-

mum of 0.14 mm².

– The shield connection to the equipotential bonding should be

as short as possible and with a contact area as large as possi-

ble (low-impedance).

– Only connect the shields to the control panel, if the latter is

also earthed.

– In case of problems due to ground loops, the shield is to be

connected to the reference ground, on the reception side, with

low impedance and, on the emission side, via a capacitor of

approximately 100nF.

– Install the device as far away as possible from noise-contain-

ing cables.

– Avoid routing signal or control cables parallel to power lines.

– Cables and their insulation should be in accordance with the

intended temperature, voltage and power ranges. The stan-

dards of the respective countries apply.

DC versions:

Use shielded wires for the counting and control inputs so as to

obtain the maximum EMC resistance or connect not used count

inputs to ground (0 V).

AC versions:

Use shielded wires for the counting and control inputs so as to

obtain the maximum EMC resistance.

www.b umer.com

ISI30, ISI31, ISI32, ISI33