Dover Markem Imaje 9330 Seguridad e información importante - Página 5
Navegue en línea o descargue pdf Seguridad e información importante para Impresora Dover Markem Imaje 9330. Dover Markem Imaje 9330 14 páginas.
Imprimir página
The printer must always be disconnected from the
mains by the mains plug before any operations
requiring it to be switched off.
Use appropriate tools for any work on the electrical
and hydraulic circuits.
When working on the ink circuit, immediately wipe
off any spillage and visually check for leaks.
After each maintenance operation, the waste
recepticles used should be emptied and cleaned.
Do not leave rags soaked with consumables near
the printer.
This unit contains a non-replaceable internal lithium
ion battery. The battery may burst or explode,
releasing hazardous chemicals. To reduce the risk
of fire or burns, do not crush, puncture, or dispose
of the battery in fire or water.
■ Recycling
Disposal of used batteries and re-
chargeable batteries (applicable in
European Union countries and other
European countries with selective
waste collection systems).
Disposal of used electrical and
electronic equipment (applicable in
European Union countries and other
European countries with selective
waste collection systems).
These
symbols
indicate
and electronic device, and the batteries and
rechargeable batteries therein, must not be
disposed of at the end of its life as ordinary
municipal solid waste. By ensuring that these
items are disposed of appropriately, you play an
active role in avoiding the harmful consequences
that incorrect disposal could have on the
environment and human health. The recycling of
materials contributes to the preservation of natural
resources.
By entrusting your end-of-life electrical devices to
a duly authorized disposal company, you ensure
that all the items therein will be handled correctly.
In all other cases and in order to safely remove
batteries,
rechargeable
materials, see the user manual or contact your
Markem-Imaje representative.
■ Waste consumables
The Consumable waste must be managed in
compliance with local regulations related to waste
management and dangerous goods transport.
Transport, transit, treatment of consumable waste
must be operated by entity owning appropriate
10106923-AA
that
the
electrical
batteries
and
other
waste management licences.
Consumable waste must be treated in compliance
with local regulations either by recycling solution
(e.g distillation), incineration with energy recovery,
incineration or specific land filling.
■ Radio
An RFID tag is fitted to each ink cartridge and
contains the set-up information of the cartridge as
required by the printer.
The printer reads the RFID tag during the
calibration process and 'pairs' with the cartridge.
The RFID radio frequency is 13.56MHz with a
maximum power limit of 10mW from the antenna.
■ FCC Rules
Caution: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
Canada, Industry Canada (IC) Notices
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada.
To reduce potential radio interference to other
users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is
subject to the following two conditions: this device
may not cause interference and this device must
accept any interference, including interference that
may cause undesired operation of the device.
For Marking & Coding Equipment. Photographs and drawings
are not binding in detail. . This document was originally written in
French. The French text of this document shall alone be authentic
English
5