Electrolux 807650601 Manual de uso y mantenimiento - Página 14
Navegue en línea o descargue pdf Manual de uso y mantenimiento para Frigorífico Electrolux 807650601. Electrolux 807650601 39 páginas.
Imprimir página4 Connecting theWater
uppiy
WARNING
To avoid electric shock, which can cause death or
severe personal
injury, disconnect the refrigerator
from electrical power before connecting a water
supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is
recommended for the water supply line° Water
supply tubing made of 1A inch plastic is not
recommended to be used, Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer wiil not be responsible for any
damage if plastic tubing is used for the supply
line.
o
o
DO NOT install water supply tubing
in areas
where temperatures
fail below freezing.
Chemicals from a malfunctioning
softener
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained
and working
properly.
iMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
Before installing the water supply line, you will need:
1. Basic Tools: adjustable wrench, flat-blade
screwdriver, and Phillips
TM
screwdriver
2. Access to a household cold water line with water
pressure between 30 and t00 psi.
3. A water supply line made of ¼ inch (6.4 mm) OD,
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of
the refrigerator to your cold water pipe. Then
add approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning (as
shown).
4. A shutoff valve to connect the water supply line
to your household water system. DO NOT use a
self-piercing type shutoff valve.
5.
Do NOT reuse compression fitting or use thread
seal tape.
6. A compression nut and ferrule (sleeve) for
connecting a copper water supply fine to the ice
maker inlet valve.
NOTE
To connect water supply line to ice maker inlet valve:
1.
Disconnect refrigerator from electric power source,
2.
Place end of water supply line into sink or bucket.
Turn ON water supply and flush supply line until
water is clear,Turn OFF water supply at shutoff valve.
3.
Remove plastic cap from water valve inlet and
discard cap.
4.
If you use copper tubing
- Slide brass
compression nut, then ferrule (sleeve) onto water
supply line. Push water supply line into water
valve inlet as far as it wilt go (¼ inch / 6.4 mm).
Slide ferrule (sleeve) into valve inlet and finger
tighten compression nut onto valve. Tighten
another half turn with a wrench; DO NOT over
tighten. See Figure 1.
If you use stainless
steel tubing
- The nut and
ferrule are already assembled on the tubing.
Slide compression nut onto valve inlet and finger
tighten compression nut onto valve. Tighten
another half turn with a wrench; DO NOT over
tighten. See Figure 2.
5.
With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel of
refrigerator as shown.
6.
Coil excess water supply line (copper tubing
only), about 2V2 turns, behind refrigerator as
shown and arrange coils so they do not vibrate or
wear against any other surface.
7.
Turn ON water supply at shutoff valve and tighten
any connections that leak.
8.
Reconnect refrigerator to electrical power source.
9.
To turn ice maker on. lower wire signal arm (freezer
ice maker) or set the ice maker's On/Off power
switch to the On position (fresh food ice maker).
Plastic Water Ti
g I/_
Steel
\_,_ P iasticwate
_im 1
to ice Maker
=_,
Clamp
_i\,
to ice m,
_ /
_--_
,F,IT_be
"I_V------
Bras_, 'I\/ fi, tu_ .4'f "_'Ill
-"
211c0mpre_ion %/
"li. Ill
LIII
"
Nut \_, ..--" ,8 Ill
" Ill..-- Ferrule
_,/"
_.tit
(Sleeve)
J
,"IIT (--. .....--? ,, I]I._staJnles,
"
[IF-
Copper '
lll stee,
wotor,,ne
Itl wa, er,,oe
I-waterVal o
,.
_
Water va ve
_,
E
?_;_
bracket
Bracket
_b_
¢J'- ,ve,n,et ///
iY)
"Zl"- o,vo,n,et
_-_L-WaterVave
ftt'
///
_2
_
{[!
///_
_
Water
valve
- Copper Water I ne
k_'X_¢i//_"-
_
f
from household
_
"_._,_
water supply
/_
rainless steel water line
.,..."
from househo d waler supply
(tn_Uodvtng
_°e° P c [ e°e gli_
°
Figure 1
Figure 2
Check with your local building authority for recommendations on water lines and associated materials prior to installing
your new refrigerator. De_ending on your locaVstate building codes, Electrolux recommends for homes with existing
valves its Smart Choice
water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an
existing valve, Electrotux recommends its Smart Choice ®water line kit 5305510264 (with a 20 ft. Copper Water Line
with self-tapping saddle valve). Please refer to v,_'w.electroluxappliances.com for more information.