AirStage ABUA24RLAV Manual de instalación - Página 3

Navegue en línea o descargue pdf Manual de instalación para Aire acondicionado AirStage ABUA24RLAV. AirStage ABUA24RLAV 17 páginas. Indoor unit (floor / ceiling type)
También para AirStage ABUA24RLAV: Manual de instrucciones (8 páginas)

• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
Request the customer to keep them on hand for future use, such as for relocating or
repairing the unit.
Request your dealer or a professional installer to install the indoor unit in accordance
with this Installation Manual. An improperly installed unit can cause serious accidents
such as water leakage, electric shock, or fi re. If the indoor unit is installed in disregard
of the instructions in the Installation Manual, it will void the manufacturer's warranty.
Do not turn ON the power until all work has been completed. Turning ON the power
before the work is completed can cause serious accidents such as electric shock or
fi re.
If refrigerant leaks while work is being carried out, ventilate the area. If the refrigerant
comes in contact with a fl ame, it produces a toxic gas.
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor
units during operation. It will cause compressor failure as well as water leakage.
First, stop the indoor unit by operating the controller, converter or external input device
and then cut the breaker.
Make sure to operate through the controller, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and
stop in the daily work.

2. ABOUT THE UNIT

1

2.1. Precautions for using R410A refrigerant

Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle. If air enters the refrigeration cycle, the pressure in the refrigeration
cycle will become abnormally high and cause the piping to rupture.
If there is a refrigerant leak, make sure that it does not exceed the concentration limit.
If a refrigerant leak exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leak occurs during operation, immediately vacate the premises and
thoroughly ventilate the area. If the refrigerant comes in contact with a fl ame, it
produces a toxic gas.
] 1

2.2. Special tool for R410A

To install a unit that uses R410A refrigerant, use dedicated tools and piping materials
that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to
use dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fi re.
Tool name
The pressure in the refrigerant system is extremely high
and cannot be measured with a conventional (R22)
gauge. To prevent erroneous mixing of other refriger-
ants, the diameter of each port has been changed. It
Gauge manifold
is recommended to use a gauge manifold with a high
pressure display range of 30in.Hg to 768 psi (–0.1 to
5.3 MPa) and a low pressure display range of 30in.Hg to
551 psi (–0.1 to 3.8 MPa).
To increase pressure resistance, the hose material and
base size were changed.
Charging hose
(The charging port thread diameter for R410A is 1/2 UNF
20 threads per inch.)
A conventional (R22) vacuum pump can be used by install-
ing a vacuum pump adapter.
Vacuum pump
Be sure that the pump oil does not back flow into the
system. Use one capable for vacuum suction of 5 Torr,
–755 mmHg (–100.7 kPa).
Gas leakage detector
Special gas leakage detector for R410A refrigerant.
WARNING
WARNING
WARNING
Changes
] 1

2.3. Accessories

For installation purposes, be sure to use the parts supplied by the manufacturer or
other prescribed parts.
The use of non-prescribed parts can cause serious accidents such as the unit falling,
water leakage, electric shock, or fi re.
• The following installation parts are furnished. Use them as required.
• Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
Name and Shape
Operating Manual
Installation Manual
Cover plate (Left)
Cover plate (Right)
Tapping screw
×
(M4
10mm)
Installation
template
Bracket (Left)
Bracket (Right)
Special nut
Wall bracket
×
Tapping screw (M4
20mm)
Coupler heat insulation
Binder
WARNING
Q'ty
Application
1
(This book)
1
1
1
2
For positioning the indoor unit
For under ceiling type
1
For suspending
the indoor unit from ceiling
1
1
4
For suspending the indoor unit on
the wall
2
For fi xing the wall bracket
6
For indoor side pipe joint
2
Large 4
For fi xing the coupler heat insulation
Medium
For power supply, transmission and
remote controller cable binding
3
En-2