DragonWave Horizon Quantum Manual de consulta rápida

Navegue en línea o descargue pdf Manual de consulta rápida para Punto de acceso inalámbrico DragonWave Horizon Quantum. DragonWave Horizon Quantum 2 páginas.

Imprimir página

All health and safety procedures and recommendations must be followed as detailed in the Horizon Quantum User Manual.

This product is to be installed and maintained by experienced telecommunications personnel only. Installations must adhere to specifications listed in the Horizon Quantum User Manual.

Horizon Quantum is to be installed with proper grounding, surge arrestors and -48 VDC power in accordance with instructions contained in the Horizon Quantum User Manual.

Mechanical

Modem (IDU)

4.3 cm x 32 cm x 22 cm; 2.4 kg

Radio (without antenna)

20 cm x 20 cm x 9 cm; 3.2 kg

Antenna Wind Loading

110 kph (70 mph) Operational

Antenna Mount Adjustment

+/- 45° Az; +/- 22° El

Radio Operating Temperature

Quantum

Standard Power + Solar Shield

DUO

High Power + Standard Power

Standard Power + Solar Shield

IDU Operating Temperature

ODU Humidity

IDU Humidity

Altitude

NEB-3 Compliant

Power

Power Input Required

Optional Adapter Available

Power Consumption:

Single Channel, Single Radio

Dual Channel, Single Radio

Dual Channel, Dual Radio

Features

Capacity w/Accelerator

Variable from 10 to 2000 Mbps full duplex CIR

2.5x capacity up to 4 Gbps with DPRM

Base Capacity

Variable from 10 to 800 Mbps full duplex CIR

2x capacity up to 1.6 Gbps with DPRM

Interface

6X1000/100/10 BaseT + 2 SFP Ports

< 200μs, Typical 120μs GigE

Latency GigE

Packet Size

64 to 9600 Bytes

Flow Control

Yes

Prioritization

8 levels served by 4 queues, based on 802.1p/q,

MPLS, DSCP ToS Bits

Modulation Shifting

Yes, Hitless

Loopback

Yes, IF , Radio, Network

XPIC

Yes, enables Co-Channel Cross Polarization

Synchronization

SynchE ready

Mounting Structures

Minimum 2 3/8" OD thick-wall (Sched. 80):

galvanized mast for 30 and 60 cm antennas

Minimum 3" OD thick-wall (Sched. 80)

galvanized mast for 90 and120 cm antennas

Minimum 4" OD thick-wall (Sched. 80)

galvanized mast for 180 cm and larger antennas

Twist and Sway

Maximum allowed twist of structure or mount

should be ½ of the antenna beamwidth. Generally

< 1° degree for 30 and 60 cm antennas, and <½°

degree for 120 cm and larger antennas. Maximum

allowed sway should be no more than 1/10th of

beam size at target.

Cables and Installation

IF cables from Horizon Qauntum modem to radio are 50 Ohm coaxial. Times Microwave LMR-

400/600/900 (and equivalents) can be ordered from DWI or vendors in 30, 60 and 90 meter lengths.

Grounding cables for radio chassis and DWI supplied surge arrestors: 6 AWG stranded bare copper.

Customer Support International Help Desk: +1 613 271 7010

Maximum Allowable Cable Loss

1.7 in x 12.75 in x 8.6 in; 5.3 lbs.

Quantum IDU Configuration

7.8 in x 7.8 in x 3.6 in; 7 lbs.

200 kph (125 mph) Survival

Single Modem with Combiner

Dual Modem with Combiner

-40°C to + 60°C (-40°F to +140° F)

Dual Modem no combiner

-40°C to + 45°C (-40°F to +113° F)

Transmit IF Frequency (Tx IF) = 400-700 MHz

DragonWave has determined that the DWI supplied patch cables (one 6‟ and one 15‟) plus two surge

-40°C to + 60°C (-40°F to +140° F)

0°C to + 50°C ( 0°F to +122° F)

arrestors add approximately 1.1 dB of extra loss @ 700 MHz, and 2.0 dB of extra loss @ 2000 MHz

100 % Condensing

Cable Type

95% Non-Condensing

(Times Microwave)

4500 m (14,760 ft)

Yes

LMR-400

LMR-600

LMR-900

-36 VDC to -60 VDC

Available Configurations

100-240VAC / 47-63 Hz to -48VDC

Single modem/Single radio

< 105 Watts

Dual modem/Single radio

< 126 Watts

Note:

2 radio licenses are required for 2 channels or 2 radio configurations.

< 172 Watts

Adjacent channel configurations are supported.

System Capacity

Horizon Quantum throughput can reach 1.6 Gbps (over the air bandwidth), depending upon hardware

and configuration:

One IF connector: (includes IF combiner)

Two IF connectors (no IF combiner)

Two radio channels on each of two Horizon Quantum units results in1600 Mbps, when

using aggregation protocols or technology.

Note:

Horizon Quantum has a compression ratio of up 2.5:1 across a link. Therefore, with

compressible data, Horizon Quantum throughput can reach 4 Gbps, depending upon

hardware and system configuration.

Surge

System Configuration

Arrestor

Logging In – Serial Port, Telnet, Web Interface

Default IP address:192.168.10.100

Super User Default Username: energetic, default password: wireless

Serial port speed: 19200 baud, 8 data bits , no stop bits, 1 parity, no flow control (19200 N81)

Default management is via Ethernet Port 3 (out of band)

Radio

Configure your pc with an IP address in the same subnet.

Command Line Interface (CLI) Overview: Serial Port or Telnet to system IP address

Coaxial

IF Cable

CLI uses GET and SET commands or config wizards with interactive question/answer.

Full context sensitive help is available for all CLI commands. Type „?‟ followed by a partial

Surge

Horizon

command.

Arrestor

Quantum

For example „? statistics‟ will provide all commands with the word „statistics'.

Pressing the TAB key after entering a partial command will complete the command if unique.

Up and down (↑ and ↓) arrow keys will recall previous CLI entries.

Ethernet

Switch

Unrecognized CLI commands will receive a NAK response.

(if req'd)

Issue „save mib‟ command to save the new settings to flash memory. Some changes require

the system to be reset to implement the new settings. („reset system‟ CLI command)

48 V DC

Rack

Web Interface (GUI) (must be enabled)

Enter the target system‟s IP address into web browser (Example: http://192.168.10.100)

Configuration Steps

Radio Band & System Mode is applied to both modems simultaneously with a single command.

Each modem supports its own frequency/channel and Tx Power (dual radio only)

email:

[email protected]

web:

http://support.dragonwaveinc.com

Quick Reference Guide

v1.2

Transmit Cable Loss

Receive Cable Loss

Budget (dB)

Receive IF Frequency (Rx IF) = 1600-1900 MHz

Single Modem,

Dual Modem,

Outer

Single IF

Single IF (20dB)

Diameter

(23dB)

(with combiner)

3/8"

351‟

301‟

9/16"

539‟

462‟

7/8"

797‟

683‟

Dual modem/Dual Radio

Modem redundancy

400 Mbps using 1 radio channel

800 Mbps using 2 radio channels

400 Mbps using 1 radio channel and 1 radio

800 Mbps using 1 radio channel on each of 2 radios (2 channels total)

Default subnet is: 255.255.0.0

DragonWave Inc.

http://www.dragonwaveinc.com

Horizon Quantum

Rel. 1.00.00

NOTE: Switch ports must be properly configured in order to pass VLAN tagged traffic.

By default all ports are considered access Ports and will only allow untagged or VLAN ID 1.

(see configuration Step 10, below)

Configure the system capacity

-get system capacity

-set system capacity <index> (setting single/dual modem or radio, or redundancy)

Note: For system capacities with „Dual Wireless Ports; a license key is required.

To check if the unit is shipped with the license key, „get licensed feature groups'.

See Index 5.

Dual Modem,

Dual IF (24dB)

If the unit is not licensed for „Dual Wireless Ports‟:

(no combiner)

367‟

Please contact

[email protected]

564‟

835‟

Configure the Radio Band.

-set radio band <radio band>

Example: set radio band fcc11_a_30

Example: set radio band fcc23_2_50_R5 (23GHz B2 50MHz Channels – Quantum Radio)

Configure the System Mode. (Web: Basic Configuration page)

-set system mode <system mode> (used for setting speed and modulation)

Example: set system mode hz30_212_256qam (212 Mbps at 256QAM modulation)

Configure the frequency bank. (Web: Basic Configuration page)

-set frequency bank <txhigh/txlow>

Review available frequency pairs and indexes. (Web: Basic Configuration page)

-get frequency bank

Program transmit and receive frequency by index. (Web: Basic Configuration page)

-set programmed frequency <index>

-set programmed frequency <index> wireless_port2 (for dual modem)

Configure the IP address, subnet mask and default gateway. (Web: Basic Configuration page)

Note: Selecting yes after either of these commands will apply the settings immediately.

-set ip address <xxx.xxx.xxx.xxx>

-set subnet mask <xxx.xxx.xxx.xxx>

-set default gateway <xxx.xxx.xxx.xxx>

Note: The user can select any user ports (P1 to P8) and data paths (DP1 to DP4) to manage the

system.

Configure the network management interface. (Web: Basic Configuration page)

set network management interface (interactive wizard)

By default the management interface is p3.

Note: By assigning the management ports as the ports belonging to an IPG the management traffic

can be isolated from other user traffic. (Out Of Band Management)

Configure Isolated Port Groups.

IPGs are used to interconnect multiple isolated networks by creating multiple switching domains.

-set ipg config <group name><enable|disable><port list>

Example:

In Band:

-set ipg config ipg5 enable p3,dp1

(enable ipg5 to correspond with port3 and dp1)

Out of Band:

-set ipg config ipg5 enable p3

(enable ipg5 to correspond with port3)

ipg = isolated port group (1-5) dp = data path (1-4).

Factory Default Configuration

IPG1

IPG2

Management port

IPG5

DP1

IPG3

DP2

DP3

IPG4

DP4

Note: It is suggested both link ends are configured the same.

To default IPGs back to default each IPG must be reprogrammed.

Rel. 1.01.00

(Web: Basic Configuration page)

or +1 (613) 271-7010.

(Web: Basic and Port Configuration page)

(11GHz B1 30MHz Channels – DUO/AP Radio)