DRAKE MPM860AG Manual - Página 4
Navegue en línea o descargue pdf Manual para Hardware informático DRAKE MPM860AG. DRAKE MPM860AG 4 páginas. Channel 3 or 4 agile processor
También para DRAKE MPM860AG: Manual (4 páginas), Manual del usuario (8 páginas)
Imprimir página6
Broadcast TV Channel Output Frequencies
TABLE 2:
CATV
BCTV
CATV
BC
TV
+100
VHF BROADCAST CHANNELS
Channel
Visual Carrier
Number
Frequency (MHz)
55.25
2
61.25
3
4
67.25
5
77.25
6
83.25
7
175.25
8
181.25
9
187.25
10
193.25
11
199.25
12
205.25
13
211.25
CATV
CATV
BC
TV
+100
UHF BROADCAST CHANNELS
Channel
Visual Carrier
Number
Frequency (MHz)
14
471.25
15
477.25
483.25
16
17
489.25
18
495.25
19
501.25
20
507.25
21
513.25
22
519.25
23
525.25
531.25
24
25
537.25
26
543.25
27
549.25
28
555.25
29
561.25
30
567.25
31
573.25
579.25
32
33
585.25
34
591.25
35
597.25
36
603.25
37
609.25
38
615.25
39
621.25
40
627.25
633.25
41
42
639.25
43
645.25
44
651.25
45
657.25
46
663.25
47
669.25
48
675.25
681.25
49
50
687.25
51
693.25
52
699.25
53
705.25
54
711.25
55
717.25
56
723.25
57
729.25
735.25
58
59
741.25
60
747.25
61
753.25
62
759.25
63
765.25
64
771.25
65
777.25
783.25
66
67
789.25
68
795.25
69
801.25
Input
Input Level:
-39 dBm / +10 dBmV, ±3 dB
Input Impedance:
75 Ohm, 18 dB return loss
Input Frequency:
Channel 3 (61.25 MHz Visual Carrier), or
Channel 4 (67.25 MHz Visual Carrier)
Output
Frequency Range:
54 MHz to 864 MHz
Standard CATV Channels 2 - 135, Normal operation
HRC, IRC Channels 1 - 135, Selected via internal jumper
Broadcast Channels 2 - 69, Selected via internal jumper
FCC Offsets:
Automatic, +12.5 kHz or +25.0 kHz channel-dependent
Output Level:
+45 dBmV
Output Impedance:
75 Ohm, 10 dB return loss
Frequency Stability:
±5 kHz
Spurious:
-60 dB @ +45 dBmV out
Broadband Noise:
-77 dBc at greater than ±12 MHz offset at +45 dBmV output,
4 MHz bandwidth
In Channel C/N:
57 dB, 4 MHz bandwidth
In Channel Frequency Response:
Within 2 dB
Output Level Note:
The output level of the MPM860AG is intended to be set at or
very near +45 dBmV. The front panel GAIN control adjusts the
input level into the conversion circuitry and not the final output
attenuation. For best noise and spurious performance please
adjust the output level to +45 dBmV with the actual input that
will be used with the device. If more than 1 to 2 dB of variation
is needed to properly equalize the system, appropriate pads
should be placed at the output of the MPM860AG.
General
DC Power Input:
+5 V ±5 % at 400 mA
+12 V ±5 % at 200 mA
Operating Temperature:
0° C to + 50° C ambient
Size:
1" W x 3.5" H x 7.5" D
Weight:
12 oz
specifications subject to change
Specifications
MPM860AG
without notice or obligation.
7