Bosch Vision 800 Series SHE68R52UC Manual de introducción

Navegue en línea o descargue pdf Manual de introducción para Lavavajillas Bosch Vision 800 Series SHE68R52UC. Bosch Vision 800 Series SHE68R52UC 2 páginas. Short instructions

Imprimir página

Getting started with your new dishwasher.

Adding Rinse Aid

— Rinse aid is necessary to improve drying results.

— Add rinse aid when the Rinse Aid symbol

the control panel illuminates.

— Lift the tab to open the rinse aid reservoir and

add liquid rinse aid by pouring over the arrow.

— Wipe up any excess rinse aid that may puddle.

Adjust Amount of Rinse Aid Dispensed

— Turn the arrow inside the rinse aid dispenser to

adjust the amount of rinse aid dispensed.

To decrease

streaks on glass

For up to 45% dryer dishes:

1 - Always use Rinse Aid

2 - Use Auto Cycle

3 - Press Sanitize button

The sanitize feature is available only in the Heavy, Auto, and

Normal wash cycles. Press the "Sanitize" button to activate the

sanitation features during these cycles.

The sanitize LED or symbol

ments are met.

Frequently Asked Questions

Dishwasher beeping after cycle end: The default settings alert

the consumer that the cycle has finished. To adjust the volume

or deactivate, refer to "Operating the Dishwasher" in the Use

and Care Manual.

Dishes are not drying properly: Refer to section above.

Odor: Debris at the bottom of the dishwasher or in the door

seal can cause odor. Clean both according to instructions in the

Use and Care Manual.

Dishwasher still on after cycle ends: Default factory settings

have the dishwasher stay powered on after a cycle ends.

Customer must manually turn the dishwasher off. Dishwasher

must be powered on again in order to start a new cycle.

9000633156 Rev A 3/11

— Use fresh powdered detergent or detergent tabs

for best results.

— 1 tablespoon will clean most loads

— 3 tablespoon max, do not overfill

— When using detergent tabs, lay them flat to avoid

contact with the cover.

To close the cover:

— Place finger on arrow and slide

cover fully left.

— Push rear end of cover down

firmly until it clicks.

To open the cover:

— Push the blue button inward

(not down) and cover will slide

open.

— Open the door and press the On/Off button to turn dishwasher on.

— Select a cycle and desired option if applicable.

— Close the door to begin the cycle.

To decrease

Cancelling a cycle / Reset the dishwasher

spots on glass

If you need to cancel a cycle or the dishwasher control panel seems to not respond,

cancel or reset by following these steps.

— Open the door slightly and press and

hold the two Cancel/Reset buttons

for 3 seconds.

— Close the door and wait about 1 min-

ute while the dishwasher drains.

will light when sanitation require-

Adding Detergent

To Start the Dishwasher

Cycle Descriptions

Heavy: Uses higher water temperature and pressure to remove

baked-on foods

Auto: Reads the size and soil of each load, adjusting water and

heat to the ideal balance for optimum cleaning results

Delicate: Uses lower water temperature and pressure, safe for

delicate or heirloom dishware

Normal: Cleans normal loads with loosely attached, normal

soiling

Express: Cleans lightly soiled loads with reduced wash time

Rinse: Rinses the soil off of a partial load and holds the dishes

until you are ready to run a full load

To Contact Customer Service

Call the toll free Customer Service number, 1-800-944-2904.

Before calling, locate the model number and serial number on

the label on the inside of the dishwasher door.

ALWAYS READ YOUR USE AND CARE MANUAL FOR DETAILED

INSTRUCTIONS AND IMPORTANT SAFETY NOTICES.

To close the cover

To open the cover

— Open the door and press the On/Off

button. If you choose to start a new

cycle, turn the unit on again and select

a cycle.

Cancel/Reset

3 Tbsp. maximum

2 Tbsp. (25ml)

1 Tbsp. (15ml)