Draper 220V Access Instrucciones de instalación y funcionamiento - Página 4
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper 220V Access. Draper 220V Access 4 páginas. Electric projection screen
Imprimir página
220V Access by Draper
Back of wall switch.
Please Note: Although both
Dry Contact and Data Cable
connections are shown, you
should only use one connec-
tion type per motor.
External Low Voltage and Wireless
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
Built-In VIC-12*
12 Volt (VIC-12) or 6 Volt (VIC-6) Relay
Green
Yellow
14 13
9
: : : :
Black
5
: : : :
1
: : : :
Brown
*These wiring diagrams are for Access screens with motor on audience left (standard), and fabric unrolling from the back of the roller (standard).
Wiring Diagrams (continued)
ILT Switch-to-Motor—Dry Contacts or Data Cable connection
Motor Data Cable
plugged in here
U
D
C
5V
P
O
O
W
M
N
M
O
N
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
Dashed wiring by electrician
Low voltage wiring by others
110/220V
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
Ring Terminal on ground wire
riveted to J-Box with Star Washer
Green/Yellow
Ground
Black
#2 Up
Brown
#1 Down
Screen Motor
Blue
Common
Jacketed Motor Cable
Wire soldered to terminal
Wire connected with Quick Disconnect
: : : :
Mounting Bracket Dimensions
12.7
9.5
38
mm
mm
mm
R 6.4
mm
3.2
35
mm
mm
6.4
mm
8
mm
R3.2
mm
www.draperinc.com
UP 5V COM DWN
Program LED
Fuse
To
Line
MC1
See separate Serial Communication-RS232 Instruction sheet for enabling
RS232 with the MC1.
8
7
5
6
4
220 VAC
3
2
1
4.8
8
mm
mm
114
mm
32
mm
122.2
mm
197
mm
228.6
mm
(765) 987-7999
Please Note: This Splitter/
Jack is located inside the junc-
tion box of your Access XL
screen.
Data Cables to switches or
to additional motors can
be plugged into any of the
three open jacks. If this is a
"Case First, Screen Later"
installation, plug the motor
cable into the jack indicated
in the drawing.
MC1
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Green/Yellow-Ground
Low Voltage Wiring by others
AC Wiring by electrician
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
To AC Line
Built-In VIC-115*
115 Volt Relay
Ring Terminal on each Ground Wire
with Star Washer screwed to Spine
Green/
Green/
Yellow
Yellow
Black
Black
Brown
Brown
Blie
Jacketed Motor Cable
Wire connected with Quick Disconnect
: : : :
4.8
mm
28.6
mm
6.4
mm
page 4 of 4
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green 110V/
Green/Yellow 220V
(Motor Ground)
Location of key
operated on-off
switch if furnished
Ground
#2 Up
220 VAC
Screen Motor
#1 Down
Common