Draper Access XL Instrucciones de instalación y funcionamiento - Página 5
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Access XL. Draper Access XL 5 páginas. Draper access xl electric projection screen
También para Draper Access XL: Instrucciones de instalación y funcionamiento (5 páginas), Manual de instrucciones (8 páginas)
Imprimir página
Access XL Instructions by Draper
Please Note: 5V DC must be
connected to be able to set
limits using the wall switch.
Back of wall switch.
Please Note: Although both
Dry Contact and Data Cable
connections are shown, you
should only use one connec-
tion type per motor.
Two-Way Serial Communication
(RS232) with MC1
White-Common to screen & 110-120V AC Neutral
Red-to Screen (directional)
Brown-to Screen (directional)
Black-Hot to 110-120V AC
Program LED
Green/Yellow-Ground
Fuse
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
MC1
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
See separate Serial Communication-RS232 Instruction sheet for enabling
RS232 with the MC1.
Built-In VIC-12/VIC-6*
12 Volt Relay
Green
14 13
9
: : : :
Red
5
: : : :
1
: : : :
Black
*These wiring diagrams are for Access XL screens with motor on audience left (standard), and fabric unrolling from the back of the roller (standard).
/
3
1
ILT Switch-to-Motor—Dry Contacts or Data Cable connection
Internal Screen Wiring
Low Voltage Wiring by others
AC Wiring by electrician
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
Ring Terminal on ground wire
riveted to J-Box with Star Washer
Green
Ground
Red
#2 Up
110-120 VAC
Black
#1 Down
Screen Motor
White
Common
Jacketed Motor Cable
Wire soldered to terminal
Wire connected with Quick Disconnect
: : : :
Mounting Bracket Dimensions
"
/
"
1
1
/
1
8
2
2
R
/
"
1
4
/
"
1
/
"
8
3
8
/
"
1
4
/
5
16
R
/
"
1
8
www.draperinc.com
INSERT MOTOR DATA
CABLE HERE
Low Voltage and Wireless Control (LVC-III)
White (Common)
Red (Up)
Black (Down)
Green (Ground)
To
110-120V
Line
8
7
5
6
4
3
2
1
/
"
3
"
16
4
1
/
"
2
"
1
1
4
/
"
13
16
7
3
/
"
4
9"
(765) 987-7999
Please Note: This Splitter/
Jack is located inside the junc-
tion box of your Access XL
screen.
Data Cables to switches or
to additional motors can
be plugged into any of the
three open jacks. If this is a
"Case First, Screen Later"
installation, plug the motor
cable into the jack indicated
in the drawing.
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
Built-In VIC-115*
115 Volt Relay
Ring Terminal on each Ground Wire
with Star Washer screwed to Spine
Green
Green
Red
Red
Black
Black
White
Jacketed Motor Cable
Wire connected with Quick Disconnect
: : : :
/
"
5
16
/
"
3
16
1
1
/
"
8
/
"
/
"
1
4
4
page 5 of 5
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
To
110/220V
Line
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
Ground
#2 Up
110-120 VAC
Screen Motor
#1 Down
Common