Draper Nocturne + E 220V Instrucciones de instalación y funcionamiento - Página 8
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Nocturne + E 220V. Draper Nocturne + E 220V 12 páginas. Outdoor electric projection screen
Imprimir página
Nocturne+ E 220V
Section 7 - Electrical Connections
CAUTION: All operating switches should be "off" before power is connected. Plug-in power cord option available with built-in low-voltage motor.
•
Screen operates on 220V
AC, 50 Hz. or 60 Hz.,
.55 Amp, 1 ph. current
draw. Duty cycle: On 28
seconds/Off 4 minutes.
Section 8 - Limit Adjustments
Please Note: Screen limits are factory set for optimum performance. Any
adjustment of these limits could void the warranty. Please check with
Draper prior to resetting screen limits.
Please Note: If Screen is "Right Hand Motor" the WHITE/DOWN
YELLOW/UP
limit screws are reversed
(II)
Figure 6
DOWN Limit (I)
+
I
DOWN Limit
Clockwise decreases
Clockwise
down travel.
decreases
down travel.
UP Limit (II)
+
UP Limit
lI
Counterclockwise
Counterclockwise
increases up travel.
increases up travel.
"Down" Limit Adjustment
(requires 5/32" (4mm) Allen wrench)
To Reduce Screen Drop:
1. Raise screen surface approximately 1'
off.
2. Turn DOWN
limit screw clockwise
(I)
3. Test by lowering screen. Repeat steps 1 & 2 until desired position is reached.
To Increase Screen Drop:
1. Lower screen to down limit.
2. With down switch on, turn DOWN
(3 screw turns = 1/2 roller revolution)
3. Test by raising screen approximately 1'
4. Repeat steps 2 and 3 until desired position reached.
Please Note: For Quiet Motor with alternate limit screws:
WHITE screw = UP and RED screw = DOWN.
•
Junction box is located inside left
endcap and cover plate secures to
endcap with two screws which may
be removed with star key or small
flat head screwdriver. Junction box
contains red, black, and white pigtail
leads and green internal ground
wire, per wiring diagram.
(Standard Motors)
and
(I)
.
(Fig. 7)
:
(I)
:
(II)
above desired setting and turn
(30cm)
(3 screw turns = 1/2 roller revolution)
limit screw counterclockwise
(I)
to increase drop.
then lower to new down limit.
(30cm)
.
(Fig. 10)
•
Screen ships complete
with internal wiring. Control
switch
may be packed
(es)
in cartons separate from
screen. Wire connecting
screen to switch
(es)
switch
to power supply
(es)
furnished by installer.
CAUTION:
- Be sure all switches are in "off" position before adjusting limit switches.
- Be prepared to shut off manually while testing.
- Screen may be damaged by lowering it too far and exposing roller.
- Motor must be installed so that limit switches are pointed down.
CAUTION: DO NOT allow dowel to wrap over roller when operating screen!
This could damage screen.
Figure 7
Motor
End
Standard Roll
Left hand motor:
White Socket—Down
Yellow Socket—Up
Right hand motor:
White Socket—Up
Yellow Socket—Down
"Up" Limit Adjustment
If Screen Raises Too High:
1. Lower screen surface approx. 1'
and turn off.
.
2. Turn UP
(II)
3. Test by advancing screen up.
4. Repeat steps 1 through 3 until desired position is reached.
If Screen Needs to Raise Higher:
1. Lower screen surface approx. 1'
and turn off.
2. With UP switch on, turn UP
(3 screw turns = 1/2 roller revolution)
3. Repeat steps 1 and 2 until desired position is reached.
Please Note: Screen must be installed
in accordance with the requirements of
the Local Building Codes, the Canadian
Electrical Code
(CEC)
the National Electric Code
and
An appropriate disconnect device shall be
provided as part of the building installation.
Please Note: Do NOT wire motors in parallel.
Motor
End
e
n c
d i e
A u
e
S i d
Reverse Roll
Left hand motor:
White Socket—Down
Yellow Socket—Up
Right hand motor:
White Socket—Up
Yellow Socket—Down
below desired setting
(30cm)
limit screw clockwise
(3 screw turns = 1/2 roller revolution).
below desired setting
(30cm)
limit screw counterclockwise
(II)
.
page 8 of 12
, CAN/CSA C22.1, and
, NFPA 70.
(NEC)
Moto
End
c k
B a
d e
S i
Wate
Left ha
White
Yellow
Right h
White
Yellow