Draper nocturne+ c Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Pantalla de proyección Draper nocturne+ c. Draper nocturne+ c 6 páginas. Outdoor crank-operated projection screen
También para Draper nocturne+ c: Instrucciones de instalación y funcionamiento (4 páginas), Manual de instrucciones (10 páginas), Instrucciones de instalación y funcionamiento (8 páginas)

Imprimir página

Nocturne+ C

Section 1 - Prepare for Installation

1. Make sure mounting surface is strong enough to hold Nocturne+.

Please Note: Installer is responsible for selecting mounting hardware

appropriate for site conditions. Ensure that fasteners are of adequate

strength and suitable for the mounting surface chosen.

2. Verify unit measurements, and make sure it will fit in desired location.

Please Note: The Dowel does not retract into Case. This will need to be

accounted for if mounting over a swinging window or door.

3. Mounting brackets MUST be installed with a gap of 1¾"

Endcap and Mounting Bracket edge

4. Drill small starter holes

(if necessary)

PLEASE READ - Safety Information

Important Safety Information

Improper installation and use of the Nocturne+ C screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to

imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.

1. Please read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail, and could

result in serious injury.

2. Installation and calibration of the unit should only be performed by an

authorized, qualified, and experienced professional.

3. Do not affix the unit to walls or ceilings that have inadequate strength

to permanently hold the unit during use. It is the owner's and installer's

responsibility to confirm the wall or ceiling to which the unit attaches is

sufficient to permanently hold the weight and stress loads of the unit at all

times. Draper

, Inc., is not responsible for improper installation, application,

testing, or workmanship related to the product at place of installation.

4. It is the installer's responsibility to make sure appropriate fasteners are used

for mounting.

5. All hardware must be installed level. Unit must be level and square.

6. Never leave the area while operating the unit during installation, maintenance,

or normal operation, unless it is secure and safe.

7. Before testing or operation, carefully inspect the entire area and path

of unit to be sure no persons or objects are in the area.

underneath)

1. Look for any job site conditions that could interfere with installation or

operation of the system.

2. Read carefully and be sure to understand all installation instructions and

all related operations manuals. These instructions are intended to serve

as a guide for the installer and owner. They should be followed closely and

combined with the expertise of experienced qualified installers. Draper, Inc., is

not responsible for improper installation, application, testing, or workmanship

related to the product at place of installation. Please retain all instructions for

future use.

between

(44mm)

. Mark wall, jamb, or ceiling.

(Fig. 1)

in mounting surface.

WARNING

(especially

Before Beginning Installation

MOUNTING

Figure 1

BRACKET

1¾"

(44mm)

E N D

Important Safety Information

8. During testing or operation, carefully watch the surrounding area for any

potential safety concerns including nearby persons or objects.

9. After installation, the entire system should be carefully tested to ensure safe

and normal operation. Extreme care should be taken during testing to remain

clear of moving parts to avoid possible injury.

10. Operation of unit should be performed only by authorized and qualified

personnel, who have been trained in its safe and effective operation and

understand its safety features.

11. The safety features of the unit should never be disabled, bypassed, or

overridden. The system should not be operated until all safety features are

properly and completely installed, calibrated, and tested.

12. Unit may need to comply with local, state, or district rules and regulations, in

particular when installed in schools. All applicable rules and regulations should

be reviewed before installation and use.

13. Failure to precisely follow installation guidelines invalidates all

warranties.

14. Custom products/installations may not be reflected in this manual. Call Draper,

Inc., if you have questions about the installation of custom products or any

questions about your installation.

3. Open cartons lengthwise.

4. Locate and lay out all pieces.

5. Inspect all boxes to make sure you have received the proper unit and parts.

6. If you have any difficulties with installing, servicing, or operating your unit, call

your dealer or Draper, Inc., 765-987-7999.

page 2 of 6

C A