Draper Paragon E Series Instrucciones de instalación y funcionamiento

Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Paragon E Series. Draper Paragon E Series 2 páginas.

Imprimir página

220V Paragon/Series E and V Electric Screen by Draper

These Installation/Operating Instructions are available in the official language of

the country where you purchase the product. Please contact your distributor to

request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à

votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen

Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen

Sie die jeweilige Verkaufs-Abteilung.

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

3 Pick up screen case from ends only. Picking case up at other points will

damage case and may damage fabric.

4 To insure a safe installation, the entire weight of the unit MUST BE

supported by the end-plates.

5 Entire bottom of screen case should be unobstructed to permit access to

bottom panel for making electrical connections or servicing.

6 Screen should be installed level (using a carpenter's level).

7 Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

8 Screen operates on 220V AC, 50 Hz., 1ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and found to

be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any responsibility

on the part of the manufacturer for improper installation or faulty workmanship at

the jobsite.

Mounting Screen

Regardless of mounting method used, the following points apply:

1 Screen should be lifted into position only by the end mounting brackets.

Keep case level by lifting end plates simultaneously to prevent surface

damage. Draper provides eyebolts to use in hoisting the screen. DO NOT

use eyebolts to mount screen. Using both mounting holes in the mounting

brackets makes for a much more stable installation. Never attempt to lift

screen along its length.

2 The entire weight of the unit MUST BE supported by the end plates to provide

a secure installation. Anchoring of the intermediate case support brackets is

typically only needed to reduce any visible case deflection when the unit is

mounted into a ceiling pocket or ceiling tile opening. For installations that are

not recessed, the amount of case deflection is usually not noticeable.

3 Screen should be positively and securely supported so that vibration or even

abusive pulling will not weaken installation.

4 Installer must insure that fasteners used are of adequate strength and suitable

for the mounting surface chosen. Installer must also insure that wall or

ceiling structure are of adequate strength. Supporting hardware (chains,

cables, rods, etc.) must be essentially vertical.

5 Entire bottom of case must be readily accessible after installation is complete.

6 Front, back and top of case must be straight—not forced to warp or bow. Use

threaded rod and support brackets to keep large cases from warping. DO NOT

use support brackets to support the weight of the screen.

7 Do not use case to support adjacent sections of ceiling.

8 If optional ceiling flange trim kits are attached, use hardware provided.

9 If case is painted, slots on bottom of case should be shielded to protect viewing

surface from paint splatters or overspray.

10 Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 220V AC, 50 Hz., 1ph. current.

Junction box is located just above the closure panel, at the motor end of screen

(left hand motor location only on Paragon). To properly remove closure panel, two

people should follow the steps on page two of these instructions. The junction

box access plate is held closed with pan head screws and may be opened with

a Phillips screwdriver. Removal of access plate exposes brown, black and blue

pigtail leads and green internal ground wire per attached wiring diagram.

Screen is shipped with internal wiring complete and control switch(es) fully boxed.

Wire connecting screen to switch(es) and switch(es) to power supply should be

furnished by installer. Connections should be made in accordance with attached

wiring diagram, and wiring should comply with national and local electrical codes.

All operating switches should be "off" before power is connected.

Please Note: Do not wire motors in parallel.

Form ParagonEV-220V_Inst13

Installation/Operating Instructions

Caution

Printed in U.S.A.

When screen is first operated, be cautious! Cycle unit down and up several times

to confirm satisfactory operation.

220V AC Single Station Control—3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

220V AC Multiple Station Control (Not CE approved)—Switches are similar

in appearance to 220 V AC Single Station Control. Screen stops when switch is

released and may be restarted in either direction. Factory adjusted limit switches

stop screen automatically when fully down or fully up.

24V Control—Three-button up-stop-down switch(es) stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop screen

when fully down or fully up. Installer should incorporate an all-pole disconnect in

the fixed wiring.

Key Operated Switching (Not CE approved)—Two kinds of key-operated

switches are optionally available with this unit. 1 The key-operated power supply

switch controls power to the screen and switches. When it is "off", the switches

will not operate screen. Key may be removed from the switch in either "on" or "off"

position. 2 A three-position key switch permits the screen to be operated directly

by key. In this case, the screen's operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Please Note: Screen limits are factory set for optimum performance of the

screen. A procedure is outlined below for minor tweaks, but any adjustment

of these limits may negatively affect the flatness of the screen surface and

could also void the warranty. Please check with Draper prior to resetting

screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches.

Caution: Rough handling in transit may cancel/reset motor limit settings.

To prevent viewing surface damage, be prepared to stop descending screen

if surface begins to retract instead of stopping or if motor does not shut off

when screen has fully retracted into case.

ADJUSTING "FULLY UP" POSITION—Put a small screw driver in the groove of

the yellow button on the motor and press vertically until hearing a "click". Raise

the screen by pressing the "up" switch on unit. Press the "stop" switch when the

screen is at the desired position. Then press the yellow button on motor until you

hear a "click", then release.

ADJUSTING "FULLY DOWN" POSITION—Put a small screw driver in the groove

of the white button on the motor and press vertically until hearing a "click". Lower

the screen by pressing the "down" switch on unit. Press the "stop" switch when the

screen is at the desired position. Then press the white button on motor until you

hear a "click", then release.

AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE ANY

PART OF SCREEN ROLLER.

½" (12/7mm) threaded

rod (for suspending

screen) by others.

" -16 (9.5mm) threaded rod

(use for adjusting

deflection in extremely

long units) by others.

203

337

brackets. NOT for

use in supporting

Knockouts for electrical connections

305 mm

(two per end) with plastic plugs*

*Left hand motor location only on Paragon

Caution: Do not remove the roller assembly from the case unless neces-

sary for repairs. If the roller assembly is removed, be sure motor is fully

re-seated in the bracket, and re-secure it carefully with the motor retaining

spring and screw (see diagram below).

Please see back page for dimensional diagrams of case and optional wall

mounting bracket, wiring diagrams and instructions on removing and replac-

ing the bottom closure.

If you encounter any difficulties installing or servicing your Paragon screen, call your dealer or

Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-1689.

Operation

Adjustments

Eyebolts for hoisting screen

(not for use in mounting

case) (do not lift screen by

center of case. To insure a

Case support

safe installation, the entire

weight of the unit MUST BE

supported by the end-plates).

weight of case.

Please note: Maximum torque for

tightening screw is 5 lb-inches.

US Patent No.

6,873,461

Suitable for use

in environmen-

tal air space

in accordance

with Section

300-22(c) of the

National Electri-

cal Code, and

Sections 2-128,

12-010(3) and

12-100 of the

Canadian Elec-

trical Code, Part

1, CSA C22.1.

Instructions

continued

on Page 2