Draper Premier Instrucciones de instalación y funcionamiento - Página 2
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Premier. Draper Premier 7 páginas. 220v premier electric projection screen
También para Draper Premier: Instrucciones de instalación y funcionamiento (2 páginas), Instrucciones de instalación y funcionamiento (2 páginas), Instrucciones de instalación (2 páginas), Instrucciones de instalación (4 páginas), Instrucciones de instalación (2 páginas), Instrucciones de instalación (2 páginas), Instrucciones de instalación y funcionamiento (4 páginas), Manual de instrucciones de instalación y funcionamiento (7 páginas)
Imprimir página
Premier
Section 2 - Electrical Connections
CAUTION: All operating switches should be "off" before power is connected. Plug-in power cord option
available with built-in low-voltage motor.
•
Screen operates on 110-120V, 60 Hz., 1.1 amp current draw. Duty cycle: On 28 seconds/Off 4 minutes.
•
Junction box is located inside left endcap and cover plate secures to endcap with two screws which may
be removed with star-head or small straight-blade screwdriver. Junction box contains red, black, and
white pigtail leads and green internal ground wire, per wiring diagram on reverse.
•
Screen ships with internal wiring complete and control switch
switch
and switch
to power supply furnished by installer.
(es)
(es)
Please Note: Screen must be installed in accordance with the requirements of the Local Building Codes,
the Canadian Electrical Code
(CEC)
appropriate disconnect device shall be provided as part of the building installation.
Please Note: Do NOT wire motors in parallel.
Section 3 - Operation
CAUTION: When operating for the first time, cycle unit down and up several times to confirm satisfactory operation. Be prepared to cut POWER if necessary.
•
110-120V SINGLE STATION CONTROL - 3-position UP-OFF-DOWN
switch permits operation to be stopped at any point. Factory adjusted
limit switches automatically stop screen when fully down or fully up.
•
24V CONTROL
(optional and requires optional LVC-IV)
STOP-DOWN switches stop at any point desired and operate in any
sequence. Factory adjusted limit switches automatically stop screen
when fully up or fully down. Installer should incorporate an all-pole
disconnect in fixed wiring available with RF or IR remote.
PLEASE READ - Safety Information
Important Safety Information
Improper installation and use of the Premier screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise installation,
mishandling of the unit during installation, or installation on an insufficient wall, or ceiling structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2. Installation and calibration of the unit should only be performed by an authorized,
qualified, and experienced professional. In particular, electrical work and wiring
[indicated in diagram by dashed lines] must be completed only by a qualified
professional electrician who has read this manual completely and is familiar with
the construction and operation of this equipment and the hazards involved.
3. Do not affix the unit to walls or ceilings that have inadequate strength to
permanently hold the unit during use. It is the owner's and installer's responsibility
to confirm the wall or ceiling to which the unit attaches is sufficient to permanently
hold the weight and stress loads of the unit at all times. Draper, Inc., is not
responsible for improper installation, application, testing, or workmanship related
to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used for
mounting.
5. All hardware must be installed level. Unit must be level and square.
6. Never leave the area while operating the unit during installation, maintenance, or
normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path
of unit to be sure no persons or objects are in the area.
underneath)
1. Look for any job site conditions that could interfere with installation or operation of
the system.
2. Read carefully and be sure to understand all installation instructions and all
related operations manuals. These instructions are intended to serve as a guide
for the installer and owner. They should be followed closely and combined with the
expertise of experienced qualified installers. Draper, Inc., is not responsible for
improper installation, application, testing, or workmanship related to the product at
place of installation. Please retain all instructions for future use.
fully boxed. Wire connecting screen to
(es)
, CAN/CSA C22.1 and the National Electric Code
- 3-button UP-
Before Beginning Installation
, NFPA 70. An
(NEC)
•
RS232 / ETHERNET - Serial communication and network communication
optionally available.
•
KEY OPERATED SWITCHING - Two key-operated switches optionally
available with this unit:
•
Key-operated power supply switch controls power to screen a
and switches. When "off", switches will not operate screen. Key may
be removed from switch in either "on" or "off" position.
•
Three-position key switch permits the screen to be operated directly
by key. Requires screen operator to have a key.
WARNING
8. Turn off power and any nearby equipment or cables carrying electricity before
connecting switches, wires, controls, or electrical components.
9. Do not wire motors in parallel without written permission from Draper, Inc.
10. During testing or operation, carefully watch the surrounding area for any potential
safety concerns including nearby persons or objects.
11. After installation, the entire system, including all sensors, should be carefully tested
to ensure safe and normal operation. Extreme care should be taken during testing
to remain clear of moving parts to avoid possible injury.
12. Operation of unit should be performed only by authorized and qualified personnel,
who have been trained in its safe and effective operation and understand its safety
features.
13. The safety features of the unit should never be disabled, bypassed, or overridden.
The system should not be operated until all safety features are properly and
completely installed, calibrated, and tested.
14. Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should be
reviewed before installation and use.
15. Failure to precisely follow installation guidelines invalidates all warranties.
16. Custom products/installations may not be reflected in this manual. Call Draper, Inc.,
(especially
if you have questions about the installation of custom products or any questions
about your installation.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.
6. If you have any difficulties with installing, servicing, or operating your unit, call your
dealer or Draper, Inc., 765-987-7999.
For reconfiguration/conversion of
non-detachable power cord to field wiring
for models PRE-28, PRE-29, and PRE-30 only:
1. Disconnect cord plug from outlet.
2. Remove junction box cover.
3. Disconnect wire nuts from black, white, and green wires.
4. Remove power cord and strain relief from screen.
5. Connect the black motor wire to "hot" supply wire.
6. Connect white motor wire to "neutral" supply wire.
7. Connect green/yellow wire to "ground"
supply wire.
8. Replace junction box cover.
Important Safety Information
page 2 of 7