Draper Ultimate Access XL V Manual de instrucciones - Página 2
Navegue en línea o descargue pdf Manual de instrucciones para Pantalla de proyección Draper Ultimate Access XL V. Draper Ultimate Access XL V 7 páginas. 220v electric projection screen
También para Draper Ultimate Access XL V: Instrucciones de instalación y funcionamiento (7 páginas)
Imprimir página
Ultimate Access XL E & V
Electric Projection Screen
Section 3 - Bottom Access Panel/Trap Door Opening & Closing
1. A spring latch near center of case and at each end of trap door holds assembly closed. Center latch must
be disengaged first.
2. To gain access to inside of screen case, disengage spring latch at center, followed by latches at each end. To
disengage, slide latch lever toward center of screen case
3. Latch levers are somewhat concealed from view. Locate these with trap door open by feeling for vertical latch
lever above the door
(approximately 3" from case endcaps and near center of
opening about 135˚.
4. Pivot prop arms at each end of trap door assembly toward ends of screen case. Prop arms engage with a hole in
each endcap to hold trap door assembly fully open.
Caution: Beware of pinch
points along closure
Figure 4
Improper installation and use of the Ultimate Access XL Projection Screen can result in serious injury or death. Primarily, injuries can occur if
the unit falls due to imprecise installation, mishandling of the unit during installation or installation on an insufficient wall or ceiling structure.
Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2. Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional. In particular, electrical work
and wiring [indicated in diagram by dashed lines] must be completed only by a
qualified professional electrician who has read this manual completely and is
familiar with the construction and operation of this equipment and the hazards
involved.
3. Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner's and installer's
responsibility to confirm the wall or ceiling to which the unit attaches is sufficient
to permanently hold the weight and stress loads of the unit at all times.
Draper, Inc., is not responsible for improper installation, application, testing or
workmanship related to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used for
mounting.
5. All hardware must be installed level. Unit must be level and square.
6. Never leave the area while operating the unit during installation, maintenance, or
normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path (especially
underneath) of unit to be sure no persons or objects are in the area.
1. Look for any job site conditions that could interfere with installation or operation
of the system.
2. Read carefully and be sure to understand all installation instructions and all
related operations manuals. These instructions are intended to serve as a guide
for the installer and owner. They should be followed closely and combined with
the expertise of experienced qualified installers. Draper, Inc., is not responsible
for improper installation, application, testing or workmanship related to the
product at place of installation. Please retain all instructions for future use.
(Fig.
3), then pull down slightly on trap door assembly.
case). Assembly will swing down,
To close trap door assembly:
1. Disengage prop arms from endcaps and pivot these
over access panel.
2. Swing trap door assembly upward, stopping just before
latch levers hit bottom flanges of endcaps
of case where
appropriate).
3. Pull levers of latches towards center of screen case to
allow trap door assembly pivot to its closed position.
4. Make sure that spring latch levers engage fully with
case endcaps
(and center of case where
WARNING
8. Turn off power and any nearby equipment or cables carrying electricity before
connecting switches, wires, controls, or electrical components.
9. Do not wire motors in parallel without written permission from Draper, Inc.
10. During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
11. After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.
12. Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.
13. The safety features of the unit should never be disabled, bypassed or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated and tested.
14. Unit may need to comply with local, state or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.
15. Failure to precisely follow installation guidelines invalidates all warranties.
16. Custom products/installations may not be reflected in this manual. Call Draper,
Inc., if you have questions about the installation of custom products or any
questions about your installation.
Before Beginning Installation
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit .
6. If you have any difficulties with installing, servicing or operating your unit , call
your dealer or Draper, Inc., (765) 987-7999.
page 2 of 7
ACCESS DOOR
ACCESS DOOR
SUPPORT
SUPPORT
BRACKET
BRACKET
I D
S L
ACCESS
ACCESS
DOOR
DOOR
LATCH
LATCH
Figure 3
(and center
appropriate).
E