Draper Crank-Operated FlexShade Instrucciones de instalación
Navegue en línea o descargue pdf Instrucciones de instalación para Mobiliario interior Draper Crank-Operated FlexShade. Draper Crank-Operated FlexShade 2 páginas.
Imprimir página
➀ Inspect all boxes to make sure you have received proper shades/parts.
Open cartons lengthwise.
➁ All endcaps, fascia, headboxes, pockets, wall clips, and other hardware
must be installed level. Shades must be level and square.
➂ There is no lower limit. Overcranking the shade past sill may cause
product to fall or otherwise fail, and invalidates warranty.
Please Note: If shade fabric is uneven, see "Field Adjustments" below.
➃ Please read the following installation guidelines thoroughly and
follow them carefully. Failure to do so may cause product to fall or
otherwise fail, and invalidates warranty.
Please Note: Custom products/installations may not be refl ected by this
document. Call Draper, Inc. if you have questions about your installation.
Crank-Operated FlexShades—Endcaps
➀ Mark wall, jamb or ceiling for placement of mounting endcaps.
Caution: Before mounting shades, verify measurements on the card
provided with the shade, and ensure the brackets are installed at the
correct width.
➁ Drill small starter hole (if necessary) in mounting surface.
➂ Mount endcaps using appropriate fasteners for surface (see Fig. 1 for
endcap dimensions). If this is a coupled unit, be sure to mount coupled
endcap in the center position. The installer is responsible for selecting
mounting hardware appropriate for site conditions.
Crank Endcap Dimensions
1
4
/
"
2
7
2
/
"
8
1
2
/
"
4
2
1
4
/
"
3"
2
1
2
/
"
4
7
/
"
5
/
"
8
8
3"
Large
➃ Insert shank into hole in center of crank assembly, then slide fabric/roller
onto shank (see Fig. 2).
➄ For coupled units see separate instruction sheet for Coupled FlexShades.
➅ Slide notched pin into idler endcap (see Fig. 2).
➆ Attach crank handle.
Idler End
Be sure retainer
clip is installed.
®
Copyright © 2009 Draper Inc.
Form CrankFlexShades_Inst09
Installation Instructions
Crank-Operated FlexShades by Draper
Caution
1
3
/
"
4
2"
5
/
"
8
7
1
/
"
8
7
/
"
8
3
3
/
"
2"
4
7
1
/
"
8
1
1
1
/
"
4
1
2
/
"
2
Small
Figure 1
Operator
Figure 2
Print ed in U.S.A.
➇ Snap end covers into place (see Fig. 3).
➀ Snap end covers onto endcaps.
➁ Follow steps 1 through 3 under "Crank Operated FlexShades—Endcaps".
➂ Remove crank handle assembly from crank (operator) endcap and remove
the washers (see Fig. 4). Insert shank into hole in center of crank assembly,
then slide fabric/roller onto shank (see Fig. 2).
➃ For coupled units see separate instruction sheet for Coupled FlexShades.
➄ Slide notched pin into idler endcap (see Fig. 2).
5
/
"
16
2"
1
/
"
4
➅ Place groove along top of fascia over endcaps, and snap into place (see
Fig. 5).
End
STEP 1
➆ Re-attach crank handle assembly to endcap (see Fig. 6). Make sure the
fascia is in place before attaching crank handle, so that the screws attach
both the handle assembly and the fascia to the endcap.
If you encounter any diffi culties installing or servicing your Crank-Operated FlexShades, call
your dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.
Figure 3
Fascia
4½"
3¼"
hardware
hardware
Figure 4
Figure 5
Standard Handle
Two-Piece Handle
Figure 6
STEP 2