Draper Motorized FlexShade Instrucciones de instalación y funcionamiento - Página 3

Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Mobiliario interior Draper Motorized FlexShade. Draper Motorized FlexShade 8 páginas. Motor operated window shades with several control options
También para Draper Motorized FlexShade: Manual de instrucciones (12 páginas)

Imprimir página
Motorized FlexShade
Section 3 - Mounting Brackets
1. Mark wall, jamb or ceiling for placement of mounting brackets.
Caution: Before mounting shades, verify measurements on the card provided with
the shade, and ensure the brackets are installed at the correct width.
2. Drill small starter hole in mounting surface
3. Attach brackets using appropriate fasteners for mounting surface.
The installer is responsible for selecting mounting hardware appropriate for site conditions.
Please Note: The brackets shown are for standard 120V motors. Hardware for other motors will vary.
4. Place operator
end onto its bracket. If a coupled unit, see separate
(motor)
instruction sheet for Coupled FlexShades.
5. Slide notched pin on idler end into slot on bracket. Slip retainer clip onto idler end
between bracket and roller
(see Fig. 2)
Idler
Idler End
Bracket
of Roller
Retainer
Clip
*Don't forget: Install retainer clip on shaft
between bracket and roller!

Section 4 - Endcaps with Fascia

Section 4.1 - Mounting Fascia to Endcaps
1. Snap endcap covers into place
2. Mark wall, jamb or ceiling for placement
of mounting endcaps.
3. Drill small starter hole
(if necessary)
in mounting surface.
4. Mount endcaps using appropriate fasteners for surface.
If this is a coupled unit, be sure to mount coupled endcap in the center position.
Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
Caution: Before mounting shades, verify measurements on the card provided with the shade,
and ensure the endcaps are installed at the correct width.
5. Place operator
end into its endcap
(motor)
6. For coupled units see separate instruction sheet for Coupled FlexShades.
7. Slide notched pin into idler endcap and attach retainer clip
Idler
Endcap
Idler End
of Roller
Retainer
Clip
*Don't forget: Install retainer clip on shaft
between bracket and roller!

(Brackets Only Installation)

(if necessary)
.
.
Figure 2
Operator
End of Roller
Please Note: Install motor so that limit
.
(see Fig. 3)
4 ½"
(114mm)
.
(see Fig. 4)
(see Fig. 4)
Motor
Figure 4
Cable
Operator
End of Roller
Please Note: Install motor so that limit
switches are pointed down
or accessible.
®
Motor
Cable
Operator
Bracket
switches are pointed
down or accessible.
Figure 3
2
/
"
7
8
(73mm)
/
"
5
8
(16mm)
2 ¼"
(57mm)
(73mm)
2 ¼"
(57mm)
3"
(76mm)
4 ½"
(114mm)
.
Operator
Endcap
CEILING MOUNTING BRACKETS
IDLER
OPERATOR
WALL MOUNTING BRACKETS
LEFT IDLER
RIGHT IDLER
LEFT MOTOR
RIGHT MOTOR
Caution:
DO NOT use wall brackets for ceiling installations.
DO NOT use ceiling brackets for wall installations.
SMALL ENDCAPS FOR FASCIA
2"
(51mm)
1
/
"
7
8
(48mm)
2
7
/
"
8
3 ¾"
(95mm)
1
/
"
7
8
(48mm)
2 ½"
(64mm)
3 ¼"
(83mm)
LARGE ENDCAPS FOR FASCIA
2
/
"
7
8
(73mm)
2 ¼"
(57mm)
4 ½"
(114mm)
2 ¼"
(57mm)
3"
(76mm)
4 ½"
(114mm)
page 3 of 8
/
"
5
16
(8mm)
2"
(51mm)
/
"
5
8
(16mm)
2
/
"
7
8
(73mm)
(9