Bosch CDG634A.0 Manual de instrucciones - Página 12
Navegue en línea o descargue pdf Manual de instrucciones para Horno Bosch CDG634A.0. Bosch CDG634A.0 36 páginas.
También para Bosch CDG634A.0: Manual del usuario e instrucciones de instalación (40 páginas)
Imprimir página
Before using for the first time
en
KBefore using for the first
time
B efore you can use your new appliance, you must
B e f o r e u s i n g f o r t h e f i r s t t i m e
make some settings. You must also clean the cooking
compartment and accessories.
Before using for the first time
Before using the appliance for the first time, enquire
about the water hardness of your tap water from your
water supplier.
So that the appliance can reliably remind you to
decalcify it when required, you must correctly set your
water hardness range.
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or
uncarbonated mineral water.
Notes
If your water is very hard, we recommend that you
■
use softened water.
If you only use softened water, you can set the water
■
hardness range to "softened" in this case.
If you use mineral water, set the water hardness
■
range to "4 very hard".
If you use mineral water, you must only use non-
■
carbonated mineral water.
Water hardness range
0
1 (up to 1.3 mmol/l)
2 (1.3 - 2.5 mmol/l)
3 (2.5 - 3.8 mmol/l)
4 (above 3.8 mmol/l)
Initial use
After connecting the appliance to the power or following
a power cut, the settings for initial use are shown on the
display. It may take a few seconds for the instruction to
appear.
You can change these settings at any time in the
Note:
basic settings. ~ "Basic settings" on page 20
Setting the language
Turn the rotary selector to set the required language.
1.
Touch the s field to confirm.
2.
The next setting appears.
Setting the time
Set the time using the rotary selector.
1.
Touch the s field to confirm.
2.
The next setting appears.
12
Setting
00 softened
01 soft
02 medium
03 hard
04 very hard
Setting the water hardness
Use the rotary selector to set the water hardness.
1.
Touch the s field to confirm.
2.
A note appears in the display confirming that the initial
use has been completed. The current time is displayed.
Switch the appliance off using the ÿ On/Off button if
you do not need to use it.
Calibrating the appliance and cleaning the
cooking compartment
The boiling point of water depends on the air pressure.
During calibration, the appliance sets itself to the
pressure ratio at the installation location. This occurs
automatically during the first steam operation. This
results in a lot of steam.
Preparing the calibration
Remove the accessories from the cooking
1.
compartment.
Remove leftover packaging, such as polystyrene
2.
pellets, from the cooking compartment.
Before calibrating the appliance, wipe the smooth
3.
surfaces in the cooking compartment with a soft,
damp cloth.
Calibrating the appliance and cleaning the cooking
compartment
Notes
The calibration can only be started once the cooking
■
compartment is cold (room temperature).
Do not open the appliance door during calibration.
■
Calibration will otherwise be interrupted.
Press the ÿ On/Off button to switch on the
1.
appliance.
Fill the water tank. ~ "Filling the water tank"
2.
on page 14
Set the specified heating type, temperature and
3.
cooking time.
Settings
Heating type
Steam S
Temperature
100 °C
Cooking time
20 minutes
Press the # On/Off button to switch on the
4.
appliance.
Wait until the cooking compartment has cooled
5.
down.
Clean the smooth surfaces with soapy water and a
6.
dish cloth.
Empty the water tank and dry the cooking
7.
compartment. ~ "After each use" on page 15
Notes
So that the appliance adapts to a new installation
■
location after moving house, reset the appliance to
the factory settings. Repeat the initial use settings
and the calibration.
The appliance saves the calibration settings, even in
■
the event of a power cut or disconnection from the
mains. Recalibration is not necessary.