Alemlube S Series Manual técnico del propietario
Navegue en línea o descargue pdf Manual técnico del propietario para Herramientas Alemlube S Series. Alemlube S Series 2 páginas. Oil hose reel
También para Alemlube S Series: Manual del usuario (2 páginas), Manual técnico del propietario (2 páginas)
Description
With covers manufactured from high quality impact resistant and UV stabilised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the new S Series SOI700 oil hose reel from Alemlube will provide you with a reliable &
cost effective means of storing and retrieving hose assemblies in your workshop. The reel can be floor, ceiling or wall mounted & the
detachable mounting bracket facilitates ease of reel mounting & storage.
Specifications
Use
Hose Length
Materials
Pressure
Weight/Dimensions
Inlet/Outlet
Working Temp
Installation Of Reel
1 For overhead ceiling mounting: install reel at most,
3m above the floor.
2 You will need to purchase appropriate hardware for
the mounting of your new reel.
3 The reel base has four 7mm (11/16") drilled holes for
mounting on a suitable flat surface. Figure 2 is a
template showing the correct location of the 4 mounting
holes in the base.
4 Using the three holes in the base, mount the reel in the
desired location. Be sure to use appropriate hardware
and to tighten the reel securely to the mounting location.
5 Apply Teflon tape or pipe sealant to the outlet fitting on the
hose & then attach to desired tool or nozzle. Check
connection for any leakage & check the reel for correct
operation. See operation section. If hose stop adjustment is
required, pull hose from reel and allow the reel to latch at the
desired length. Loosen hose stop bolts and slide hose stop to
a position close to the hose guide. Tighten hose stop bolts
and unlatch the reel.
Operation
1 Check your S Series reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2 Latching mode switch, when your S Series reel is in free run state, pull out
the hose and allow it to retract after hearing the first, second or third click.
3 To unlatch the reel, slowly pull out the hose until the clicking noise stops, and
then let the hose retract unitl the hose stop rests against the hose guide.
4 NOTE: To avoid damage to your S Series reel, always hold onto the hose while it is rewinding. Periodically check the hose
condition for wear or damage and check the swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1 Make sure incoming line pressure does not exceed the rated operating pressure for your model hose reel.
2 Use proper eye protection when assembling and using the hose reel.
3 Use soap and water when checking for leaks.
4 Keep children away from the work area.
NSW/ACT
QLD/PNG
TEL: (02) 9939 0711
TEL: (07) 3204 9166
FAX: (02) 9939 0411
FAX: (07) 3204 1224
OWNER'S TECHNICAL MANUAL
S Series Oil Hose Reel
Oil
S.A.E 100R1 rubber, 10m x 12mm ID hose
Plastic covers, steel spring & Buna "N" seals
2000psi (138 bar)
15.6kg / 490mm (L) x 448mm (H) x 228mm (W)
1/2" BSPT(m)
-30°C ~ 100°C
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
Visit our website at
www.alemlube.com.au
WA
SA/NT
TEL: (08) 9302 4199
TEL: (08) 8241 7111
FAX: (08) 9303 2095
FAX: (08) 8241 7011
or
www.alemlube.co.nz
SOI700
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008