Description
With covers manufactured from high quality impact resistant and UV stabilised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the EL series reels from Alemlube will provide you with a reliable cost effective means
of storing and retrieving hose assemblies in your workshop. The reels can be floor, ceiling or wall mounted and the detachable mounting
bracket facilitates ease of reel mounting & storage (if required). Each reel is tested for its ability to hold pressure & hose retraction prior
to leaving the factory & adherence to stringent assembly & operation standards guarantees you years of trouble free operation. Non snag
roller guide assemblies, crimped hose ends, dependable swivel & spring assemblies are features that ensure trouble free hose storage
& retrieval.
Specifications
Use
Hose lengths
Materials
Pressure
Weight/Dimensions
Inlet/Outlet
Working Temp
Installation of Reel
1 For overhead ceiling mounting: install reel at most 3 metres
above the floor.
2 You will need to purchase appropriate hardware for the mounting
of your new reel.
3 The reel base has three 10.5mm (13/32") drilled holes for
mounting on a suitable flat surface. Figure 3 is a template
showing the correct location of the 3 mounting holes in the base.
4 Using the three holes in the base, mount the reel in the desired
location. Be sure to use appropriate hardware and to tighten the
reel securely to the mounting location.
5 Apply teflon tape or pipe sealant to the outlet fitting on the reel
hose. Check connection for any leakage & check the reel for
correct operation. See operation section. If hose stop
adjustment is required, pull hose from reel and allow the reel to
latch at the desired length. Loosen hose stop bolts and slide
hose stop to a position close to the hose guide. Tighten hose
stop bolts and unlatch the reel.
Operation
1 Check your reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2 Latching mode switch, when your reel is in free run state, pull out the hose and allow it to retract after hearing the first, second or
third click.
3 To unlatch the reel, slowly pull out the hose until the clicking noise stops, and then let the hose retract until the hose stop rests
against the hose guide.
4 NOTE: To avoid damage to your reel, always hold onto the hose while it is rewinding. Periodically check the hose condition for
wear or damage and check the swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1 Make sure incoming line pressure does not exceed the rated operating pressure for your model hose reel.
2 Use proper eye protection when assembling and using the hose reel.
3 Use soap and water when checking for leaks.
4 Keep children away from the work area.
Head Office NSW
VIC
TEL: (02) 9939 0711
TEL: (03) 8787 8288
FAX: (02) 9939 0411
FAX: (03) 8787 8266
Visit our website at
EL SERIES
Ideal for all high flow air applications including rattle guns, etc.
15m of 12.5mm ID hose
Plastic covers, steel spring & buna "N" seals
290psi, (20 bar)
10Kgs / 480mm (L) x 470mm (H) x 230mm (W)
1/2" BSPT(m) 1/2" BSPT(m)
0°c – 50°c
QLD
TEL: (07) 3889 8480
FAX: (07) 3889 8490
www.alemlube.com.au
SERVICE INSTRUCTIONS
HR40020
ir & Water Hose Reel
S /NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
W
T S
TEL: (08) 9209 3066
TEL: (03) 6343 0477
FAX: (08) 9209 3933
FAX: (03) 6343 0911
Imprimir página