Drayton 22092 Instrucciones de uso

Navegue en línea o descargue pdf Instrucciones de uso para Termostato Drayton 22092. Drayton 22092 2 páginas. Programmable room thermostat 5-2 day / 7 day
También para Drayton 22092: Instrucciones de instalación (2 páginas), Manual del usuario (14 páginas), Manual de inicio rápido (2 páginas)

Imprimir página
Drayton 22092 Instrucciones de uso
06490098001 IssA 24-1-07
13/2/07
12:04
Page 1
Drayton
Digistat +3RF
Programmable Room
Thermostat Wireless
5-2 Day / 7 Day
Model: RF701/22092
Power Supply:
Battery - Thermostat
Mains
- Digistat SCR
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
Customer Service Fax: 0845 130 0622
Certification Mark
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
User Guide 06490098001 IssA
User Instructions
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set 'On' and 'Off' time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18
o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won't have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don't
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, 'Override', 'Advance' or 'Boost'. These are explained in the
manufacturer's instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
Your Digistat +3RF
The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.
Clock Setting
Your Digistat +3RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Digistat +3RF set to your new temperature
until the next pre-programmed event (at which time it will revert

Basic Settings

to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The
indicator will
show on the screen if the heating is turned on.
A flashing flame
indicates the product is in intelligent delayed
start mode (see special note).
Controls and Display Layout
Drayton
Digistat +3RF
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate "low battery" during this time the Digistat +3RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Digistat +3RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
(Fig 1)
(Fig 2)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
To adjust the times and temperatures for 5-2 Day
operation:
2. Press the
(Fig 3)
3. Once time has been set,
The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.
Digistat +3RF
Pre-set Program
Your Digistat +3RF comes with the following default settings
4. Once the last weekday
pre-programmed for your convenience:
Pre-set Program 1 (9 til 5)
Monday-Friday
Event
1
2
3
4
5
6
Time
6:30
8:30
12:00
14:00
16:30
22:30
Temperature
20.0
16.0
16.0
16.0
21.0
7.0
Saturday-Sunday
5. Once the final temperature
Event
1
2
3
4
5
6
Time
7:00
9:00
12:00
14:00
16:00
23:00
Temperature
20.0
18.0
21.0
18.0
21.0
7.0
Weekday
25ºC
20ºC
15ºC
10ºC
5ºC
1
2
3
4
5
6
06:30
08:30
12:00
14:00
16:30
22:30
Time Period Monday-Friday
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is dropped
from 20ºC down to16ºC, it stays at 16ºC throughout the day, until
16:30 when the temperature increases to 21ºC. The temperature
then drops down to a night-setback temperature of 7ºC until 06:30
when the cycle repeats for the next day. (Monday to Friday) or
changes to weekend setting see below.
Weekend
25ºC
20ºC
15ºC
10ºC
5ºC
1
2
3
4
5
6
07:00
09:00
12:00
14:00
16:00
23:00
Time Period Saturday-Sunday
As you can see, at 07:00, the heating will come on to raise the
temperature to 20ºC. At 09:00, the temperature set point is
dropped from 20ºC down to18ºC, it stays at 18ºC until 12:00 when
the heating comes on to raise the temperature to 21ºC. The
temperature stays at 21ºC until 14:00 when it drops down to 18ºC.
At 16:30 the heating comes on to raise the temperature to 21ºC
where it stays until 23:00 when the temperature then drops down
to a night-setback temperature of 7ºC until 07:00 when the cycle
repeats for the next day. (Saturday and Sunday) or changes to
weekday settings see above.
To adjust the times and temperatures for 7-Day
operation:
1. With the product operating
1. With the product operating
as normal in the Auto mode
press
once and then
press the + button until the
display is flashing and shows.
once, the
2. Press the
display will be as shown. The
time will be flashing, use the
+ or - buttons to adjust the
1st time as required.
3. Once time has been set,
press
and use the
+ or - button to adjust
required temperature
(shown flashing).
Press
to confirm and
move to the next time and
temperature periods to be
(* small 1 in lower half of screen
adjusted confirming changes
shows which time period is being set
by pressing
button.
e.g. 1=1st period, 2 = 2nd period etc)
(max 6 periods).
4. Once Monday has been set,
temperature has been set
press
once to confirm
settings and allow adjustment
of the weekend program.
Use the + and – butons and
5. Once the final temperature
the
button to set the 6
periods for the weekend program.
has been set press
to
confirm setting. To exit press
or
until you
return to auto mode with the
bottom arrow pointing at Auto.
Congratulations!
The unit is now set correctly to follow your required timings.
as normal in the Auto mode
press
once and then
press the + button until the
display is flashing and shows.
once, the
display will be as shown. The
time will be flashing, use the
+ or - buttons to adjust the
1st time as required.
press
and use the
+ or - buttons to adjust
required temperature.
Repeat the above steps
2-3 until the 6 periods
have been set for Monday
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
press
once.
Repeat steps 2-3 until all
7 days of the week have
been set.
has been set press the
to confirm settings. To exit
press
or
until
you return to auto mode with
the bottom arrow pointing
at Auto.
Congratulations!
The unit is now set correctly to follow your required timings.