Carlisle Fluid Technologies TC-IR3LT-02 Manual de servicio - Página 5

Navegue en línea o descargue pdf Manual de servicio para Equipos de servicio Carlisle Fluid Technologies TC-IR3LT-02. Carlisle Fluid Technologies TC-IR3LT-02 12 páginas.

Imprimir página

TRU CURE IR3L/IR3LT – GENERAL INFORMATION

FIELD OF APPLICATION

The Trisk Devilbiss IR3L/IR3LT are designed to provide an

accelerated and even cure of most automotive refinishing

materials. Typically drying of putty, filler, base and top coats,

both water-based and solvent-based products. Its site of use is

the preparation area and finishing area. Within the automotive

industry and vehicle repair sectors, it is used to dry small areas

and cure materials before polishing .

PRODUCT DESCRIPTION

The easily maneuverable Trisk Devilbiss IR3L/IR3LT are

equipped with both dual and single lamp cassettes for easy

adjustment and flexibility around curved parts without sacrifice

to heat distribution. The design, combined with a gas spring,

makes cassette adjustment simple. The IR lamps and reflectors

are protected against mechanical damage with a mesh. The

control unit enables flash off (50% power) and full bake

(100% power). The time can be set individually for each mode

(0-30 min). Additionally, the IR3LT unit is equipped with a

contactless temperature control where the temperature can be

set between 20°C and 99°C.

PARTICULAR ADVANTAGES

Unique reflector design

The Trisk Devilbiss IR3L/IR3LT features a unique dimpled sheet

reflector that generates extremely even curing intensity and

temperature over entire surfaces. This ensures the fastest

possible curing time, while minimizing risk of over-curing or

burning sections of your coating.

Good maneuverability

The Trisk Devilbiss IR3L/IR3LT are sized to cure higher

surfaces such as hood and roof. Lockable gas piston makes it

very easy to set point of parallel arm. IR3LT has a laser guided

pyrometer displaying surface temperature readout which make

it even easier to properly position the lamps.

TECHNICAL DATA

Electrical diagram, see page 10.

Rated Voltage

Rated power

Heating elements

Fuse*

Weight

Noise level

Max ambient temperature

during operation

Max ambient temperature

during storage and

transportation

* The dryer must be supplied by recommended fuse.

SB-81-011-R1 (12/2022)

220V - 240 V, 50/60Hz Single Phase

3 emitters, full power 3000 W

3 quartz, tungsten filament,

Infrared emitters

16 A slow, type C (UK 13A) (NA 20

48 kg

Less than 70 dB (A)

INSTRUCTION TO THE OWNER

The owner of the mobile dryer must produce clear operating

instructions, adapted to local site conditions and applicable

national / regional requirements, and make these available to

all users.

Mobile dryer users must adhere to these operating instructions.

The mobile dryer user must always ensure that sufficient

technical ventilation is complied in accordance with the

applicable national / regional requirements.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Children

should be supervised to ensure that they do not play with the

appliance.

Dispose of spent items at the nearest environmental protection

facility for recycling.

WARNINGS

FIRE AND EXPLOSION

Do not use in an area until it is checked and cleared

of combustible and/or flammable materials.

Do not use in an area where the air may contain

flammable dust, gas, or liquid vapors.

Never direct the heating equipment towards any

pressurized vessel.

Never direct the heating equipment towards

combustible or flammable materials.

If you have a distance less than 60 cm/2 feet to the

object the temperature might raise quickly and the

risk for fire increases.

ELECTRICAL EQUIPMENT

The mobile dryer is operated by highly dangerous

electrical voltage.

ACCESSING ELECTRICAL EQUIPMENT

Before accessing live parts, remove the main

connector from the wall socket. Only professional

electricians may have direct access into the electrical

equipment.

If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

WARNING!

Intensive heat radiation. Hands, face and other parts

of the body should be exposed as little as possible to

the heat radiation.

5 / 12